Brake Pads and Rotors
VW Polo
Volvo S60
Grand Am SE

How do you change brake pads on a 2000 Grand Am SE?

444546

Top Answer
User Avatar
Wiki User
Answered
2009-07-26 23:01:32
2009-07-26 23:01:32

Go to the brake cylinder reservoir open the cap, this will release any back pressure in your break line when you compress your piston back in place. after you remove the wheel, three's going to be two bolts on the inside of the brake caliper. if i can remember right they should be half inch bolts...take them out and the caliper assembly should be able to be pulled up and off. slide out the old brake pads, and then use a pipe clamp or some sort of clamp to compress the piston on the caliper. don't go too fast or you'll get brake fluid everywhere just go slow and compress it all the way in. then put on your new pads, slip the assembly back over the rotor, and tighten the bolts back in, but put some locktite thread glue on the bolts, or they might vibrate loose. tighten down the bolts and you're done. hope this helps

012
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


How do you change brake pads for a 2000 Nissan Quest?

How do you change the front and rear brake pads on a 2000 Honda Civic Si?

If you need to ask this question on the internet, you should NOT be doing it yourself.

The emergency brakes are whatever your rear brake pads are.

How do you change brake pads on a 2002 Nissan Sentra? How do you change brake pads on a 2002 Nissan Sentra? How do you change brake pads on a 2002 Nissan Sentra?

Unless the caliper is broken, you can just replace the brake pads.

you buy brake pads and you change them

how to change front brake pads on a 1994 lexus es300

Lift the car, remove the tire, remove the brake shoe/calipers and remove the old brake pads. Put in the new brake pads, replace the brake shoe/calipers, replace the tire and lower the car.

How do I change the brake pads on Toyota tacoma 2007

how to change front brake pads on a 2003 neon

You can change the brake pads by first removing the wheel. Remove the brake and retaining springs. Reverse the process to install the new brake pads.

remove old brake pads, replace with new brake pads voila!

how do i change rear brake pads on 53 plate Picasso hdi

Lift the car on a jack, remove the tire and set aside, remove the brake shoe/caliper, and remove the old brake pads. Put in the new brake pads, replace the brake shoe/calipers, replace the tire and lower the car.

Lift the vehicle with a jack, remove the tire, remove the brake shoe/calipers, and remove the old brake pads. Next, put in the new brake pads, replace the brake shoe/calipers, replace the tire and lower the vehicle.

You can change the brake pads on your 2007 Honda by removing the wheel. Remove the brake pad springs. The brake pads will come off. Reverse the process to install the new brake pads.

You will need to remove the tire and wheel from your 1998 Pontiac Grand Am. Remove the brake assembly spring from the brake pads. The brake pads will come off. Reverse the process to install the new brake pads.

if you need to ask how to change the brake pads on a vehical. Please do not touch them. Cause nobody wants you slamming into the back of there car cause you f*@ked up!

is it hard to change brake pads on a 1989 BMW 735i

http://www.justanswer.com/questions/24dnv-change-front-brake-pads-renault

How do you change the rear brake pads on a 2010 Chevy Malibu

In order to change the brake pads, you must first remove the wheel. Remove the retaining clips and the brake pads will come off. Reverse the process to install the new pads.

you have to remove the caliper to access the brake pads


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.