0
Remove 4 bolts attatching the hood on,remove side engine covers,remove battery and tray, remove headlight assy ,unplug and remove 2 plugs on harness connected to the motor,remove air filter asembly, throttle and choke linkage, remove fuel pump line from engine,remove pump and 4 bolts holding in motor, remove 4 bolts holding driveshaft on and tap loose with rubber mallet, engine is now loose from chassis. remove both side shroud covers, and remaining shroud around flywheel, 2 bolts and you finally have the starter out. best to take to local starter rebuild shop the stealership wants like 400 bucks for these. assembly is reverse of removal
Wiki User
∙ 14y ago
Wiki User
∙ 14y agoYou change the starter cord carefully to avoid having the spring jump out of the starter case. If that happens, you really have problems as the 350 G was made by echo. The part number is 177200.23532 for the entire starter assembly if you can locate it. The pulley will need to be carefully removed and taken apart to insert a new pull cord. You should be able to duplicate the knot and rewind the pull cord and reinsert it into the housing in the appropriate place to maintain the spring tension on the cord. If the spring jumps out of the housing, you have a real problem!
Wiki User
∙ 10y agoNot that it is what you want to especially hear, but you must pull the engine so that you can remove the shrouds that are in the way. Takes a good mechanic about three and a half hours, and others as long as it takes.
Wiki User
∙ 13y agoengine must be hoisted off the frame at least 6 inches, you can leave everything hooked up except the drive shaftwill come off and need to be guided back into place as you set the engine back doun when finished. If you are not an experienced mechanic dont try this.
Wiki User
∙ 12y agoeasy 1st remove Ur battery tray!
2nd remove the nuts in the 3 places!
3rd take it out or if u can't see remove the mower deck to see what u are doing! and then put the new one in the same way!
Wiki User
∙ 10y agoRemove the motor. Lifting the motor six inches will give access to the starter
Wiki User
∙ 10y agohow to change a starter on a 6400 johndeere
Add your answer:
Earn +20 pts
How do you trouble shoot John deere Lt 155 solenoid?
I have a JD LT 155 C. I have replaced the solenoid and the mower still want start. There is 12 volts between the battery and the solenoid. When I test the voltage between the solenoid and the starter, the reading is 5 to 6 volts. Why is there a drop in the voltage to the starter?
What auto solenoid fits john deere mower L111?
The starter solenoid for most old Fords will work. If you need something specific, a 1975 Ford F-150 starter solenoid will work. Just make sure your replacement solenoid has 2 large posts and 2 small posts. (They all have 2 large posts, its the number of small posts thats important). You can also order an exact replacement for about $15 here: http://www.greenpartstore.com/John-Deere-Starter-Solenoid-Kit--AM138497_p_5144.html Good luck!
Where is the fuel solenoid on a john deere 4300?
Answer The Question Clown!
How do you replace starter assembly on S1400 John Deere trimmer?
How to remove starter assembly
How do you change a drive belt on a John Deere LT 190?
How Do I change A drive belt on a John Deere LT190?
How do you change oil john Deere GX85 lawn mover?
how to change oil on JOHN DEERe GX 85
What starter fits a john deere lt133 mower?
The correct one.
Where is the fuel shut off solenoid on a john deere gx345?
under the float bowl on the carburetor
How do you change the oil in a John Deere 1050 tractor?
oil capacity of a john deere 1050
How do you change drive-belt on a John Deere T155?
how do you tighten belt on T155 john deere
Does the starter solenoid charge the battery on john deere275 mower?
the starter solenoid only engages the starter when the key switch is activated. the alternator is what charges the battery which is located under or along side the flywheel
How do you change a pull string on a John Deere JS60 push mower?
Frankly, it is pretty easy - but hard to believe you can't just replace the pull cord! You have to spend about $45 (w/ shipping) instead on: John Deere Recoil Starter Assembly - LG497680
