answersLogoWhite

0


Best Answer
Copy

The best answer is to take it to a dealer. They should install a new one for free. There is a recall (WXX81) for 1996 to 1998 Legacys.

User Avatar

Wiki User

โˆ™ 2015-07-15 21:15:26
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you change the alternator on a 1993 Subaru Legacy?
Write your answer...
Submit

Related Questions

1993 subaru legacy rough idle- what could be causing it?

If an alternator is going bad it can cause a rough idle in a 1993 Subaru Legacy. Cold temperatures in the winter can also cause a rough idle in the Subaru Legacy.


Is 1993 subaru legacy an interference engine?

no it is not


What year fronts seats in 1991 Subaru Legacy are interchangeable?

In general, many of the 1990 through 1993 parts are interchangeable on the Subaru Legacys. But your best source would be a 1991 Subaru Legacy, followed by a 1990 Subaru Legacy. Verify the bolt patters before purchasing from 1992 or 1993.


I need a dipstick for a 1993 subaru legacy?

Go to a junkyard


How do you change the blower motor on a 1993 Subaru Legacy?

Remove the glovebox and brace. The blower motor is mounted there with 3 screws


Where is the fuel pump on a 1993 subaru legacy?

The fuel pump is located in the fuel tank on a 1993 Legacy. There should be an access panel inside of the vehicle to get to the pump.


What is the ignition timing supposed for a 2.2L 1993 subaru legacy?

The 1993 Subaru Legacy 2.2 liter engine ignition timing is the sequence that allows the engine to run smoothly. The ignition timing is synchronized with the crankshaft position sensor.


1993 subaru legacy automatic seat belt?

The 1993 Subaru Legacy was equipped with automatic seat belts to help improve passenger safety. This ensured that drivers and passengers would no longer forget to put their seat belt on.


How do you adjust a 1993 subaru legacy carburetor?

its fuel injected, no carb on that bad boy


How do you open the fuse panel on a 1993 subaru legacy?

im having the same problem...


Will a subaru 1993 legacy motor fit in a 2000 outback both standers?

yes


Will a 91 Subaru legacy auto transmission fit in a 90 Subaru legacy?

the 1989 through 1993 subarus were one series. should bolt on so long as the engine is the same model.


How many oxygen sensors does a 1993 Subaru Legacy non -turbo have?

1 on the 2.2


Where is the transmission fluid located on a 1993 Subaru Legacy?

it is ordinarily in the transmission. or, it could be in a can at the parts store.


What transmission fluid does a 1993 Subaru Legacy take?

The standard Dexron III most vehicles use.


Where is the thermostat located in a 1993 subaru legacy?

bottom -front of block, follow the lower rad hose to it.


What is the rocker arm bolt torque sequence 1993 subaru legacy 2.2 liter?

17 pounds


What is fuel tank size on a 1993 subaru legacy wagon?

It is 15.9 gallons. Source the owners manual.


Where is the turn signal relay in a 93 subaru legacy located?

The turn signal relay for the 1993 Subaru Legacy is located behind the left hand instrument panel. Look on the left hand side of the steering column.


How do you replace an alternator on a 1993 Isuzu Trooper V6 3.2L LS?

how to change an alternator


How many exhaust tips are on a 1993 subaru legacy wagon?

On a stock exhaust, there is one muffler and two tips


Where is the oil pressure switch located on a 1993 Subaru Impreza 2WD?

directly underneath the alternator on the engine block


Where can you find the dash wiring diagram for a 1993 Subaru Legacy with turbo?

www.bbs.legacycentral.org is a GREAT resource for the first generation Legacy. Search that site. Huge amounts of info there.


Where is the fuse box in a 1993 subaru legacy?

There's two. One under driver dash and one under the hood


How do you change an alternator belt for an 1993 vr4 galant?

You can remove your 1993 Mitsubishi alternator belt by loosening the tensioner pulley. Slide the tensioner pulley to the right. The alternator belt will become loose and can be removed. Reverse the process to put the new alternator belt on.