answersLogoWhite

0


Best Answer

remove wheels thenremove calipers the rotors are on the studs with small keeper washers just pry them off

User Avatar

Wiki User

โˆ™ 2006-12-30 02:40:03
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you change the front brake rotors on a 2000 Jeep Grand Cherokee?
Write your answer...
Submit
Related questions

Where are the wheel bearings located on a 2004 jeep grand Cherokee?

In the brake rotors.


Where is the emergency brake adjustment on a 99 grand Cherokee?

The main adjustment is done at the rear brake shoes inside the rear rotors.


How do you change rotors on a 1997 Jeep Grand Cherokee Laredo?

Remove the wheel; remove the brake pads and caliper; the rotor should slide off of the lug bolts.


You have 2004 Jeep Grand Cherokee Laredo brake and abs light is on how can you fix it?

How to change the brake switch on a 2004 Jeep grand Cherokee Laredo


Why does your 2001 Jeep Grand Cherokee Laredo steering vibrate when you apply the brakes?

Warped brake rotors. This is a very common problem for the 1999-2004 Grand Cherokees. You will need to have your rotors replaced, or resurfaced. The best resurface method is with an on car brake lathe.


How do you change brake light switch on 93 Jeep Grand Cherokee?

The 1993 Jeep grand Cherokee brake light switch simply plugs in and out. The brake light switch is located beneath the dashboard on the drivers side of the engine compartment.


How do you change the front brake rotors on a 1996 jeep grand Cherokee?

Should peel off" Remove wheels Remove caliper mounting bolts Slide caliper off rotor Rotor should slide off hub


Are there printed instructions to change rear brake rotors and pads on 2001 Jeep Grand Cherokee Limited?

Buy yourself a Hayne's or Chilton's repair manual at any auto parts store. Here you will find the info you are looking for.


What would be causing a scrubbing noise in rear brakes when you already replaced brake pads in a 96 grand jeep Cherokee Laredo?

The brake pads might not be adjusted properly. The brake pads can be too tight and have contact with the rotors.


How do you change front brake rotors on a 1998 Hyundai Accent?

Change front brake rotors on a 1998 Hyundai Accent?


1989 jeep Cherokee front disc brakes pulling hard to one side is there an adjustment that could be made other then bleeding brakes?

change calipers and brake lines. flush brake system. measure rotors for thickness. the rotors on your particular vehicle are composite, which usually warrants replacement rather than to turn them. do all of this due to the age of the vehicle. change calipers and brake lines. flush brake system. measure rotors for thickness. the rotors on your particular vehicle are composite, which usually warrants replacement rather than to turn them. do all of this due to the age of the vehicle. change calipers and brake lines. flush brake system. measure rotors for thickness. the rotors on your particular vehicle are composite, which usually warrants replacement rather than to turn them. do all of this due to the age of the vehicle. change calipers and brake lines. flush brake system. measure rotors for thickness. the rotors on your particular vehicle are composite, which usually warrants replacement rather than to turn them. do all of this due to the age of the vehicle.


How to change the rotors on a 1991 Honda Civic?

To change the brake rotors on a 1991 Honda Civic raise the vehicle. Remove the wheels and brake caliper bracket. Remove the brake pads. Loosen the rotor mounting screws and replace the rotors.


When you brake the car starts to vibreat?

Change the brake rotors


How many miles before you should change your rotors?

As long as your rotors are not warped, or you have not let the brake pads wear to the point they defaced the rotors, there is no need to change them. Just install new brake pads. Rotors can last the life of the car.


Can you change a 94 grand Cherokee rear brake to a 95 rear disc brake?

Not unless you also change the wheel hub. This might require a complete rebuild of the rear axle.


How do you change rear brake rotors on 2000 VW Beetle?

Remove the brake assembly from your 2000 VW Beetle. Tap on the rotors with a hammer or mallet until the become loose. Slide the brake rotors off. Reverse the process to install your new brake rotors.


How do you change 1999 ford explorer front brake rotors?

remove the brake caliper and the rotors come right off


What should it cost to replace brake pads on a Jeep Grand Cherokee?

Omaha nebraska....Jensen tire at 132nd and center. Just paid $500 to replace rotors and pads. Hard to swallow!


How does the emergency brake work on a 2003 Jeep Grand Cherokee?

The emergency or parking brake on 2003 Jeep Grand Cherokee operates a set of brake shoes inside a hub on the rear axles, this is incorporated into the disc brake setup.


How do you change front brake rotors on your 95 blazer?

It can be easy to change the brake rotors. Lift the car, remove the tire, brake shoe and rotor, put on the new rotor, replace the brake shoe, tire and lower the car.


How do you change front brake rotors on lexus GS300?

It is important for a person to learn how to change the brake rotors. A person needs to lift the car, remove the tire, brake shoe and rotor, put on the new rotor, replace the brake shoe tire and then lower the car.


Is it necessary to change brake pads when changing rotors?

When rotors need to be changed usually the pads have worn down. It is always a good idea to change pads when changing rotors.


How do you change rotors on a 1991 accord?

remove tire calipers brake assembly then pull your rotors off i would recomend putting new brake pads if your putting new rotors you will need a special puller for the rotors cause they are pressed on


Why does a 1994 grand marquis wobble when driving?

Could be the tires, or your front brake rotors


Where can I locate instructions on how to change the brake rotors in my car?

Brake rotors are suppose to be easy to change out if your a mechanic and know how to use tools. It is also a good idea to leave it to a professional if your not very familiar with what you are doing.