answersLogoWhite

0


Best Answer

there are about 3 special tools required to do this job. It includes removing the steering wheel, horn assy., and the spring loaded center support.

User Avatar

Wiki User

โˆ™ 2006-03-07 01:44:25
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you change the ignition key lock in a 1979 Camaro Z28?
Write your answer...
Submit
Related questions

What do you do when the Key won't turn the in dash ignition on a 1999 grand am se?

change the Ignition Lock lock switch


Change ignition lock on 1970 ford maverick?

How do I replace an Ignition in a 1970 Maverick


How do you change the ignition lock cylinder in a 2001 Chevrolet Tracker?

To change the ignition lock cylinder in a 2001 Chevrolet Tracker, first disarm the air bag system. Then remove the clock spring assembly to be able to remove the old ignition lock cylinder and replace with a new.


Do you need to change the key chip if you change the ignition switch in a terrano?

The ignition switch should be separate from the ignition key/lock assembly, so I'll say no.


Can a locksmith change an ignition lock set?

On most cars, yes.


How do I get the dashboard ignition switch out to replace my lost ignition key on my 1979 ford bronco?

There is a lock ring on the inside of the dash where the switch connects. You need to remove this lock ring to remove the switch from the dash.


Do you have to reset vats on 1992 camaro after changing ignition?

No. You have to get a key cut with the correct value resistor in it. The new lock cylinder comes with a key with no chip.


Where is the pass-key located on a 1994 Chevrolet Camaro?

If you have a pass key light "on" then in all probability it is a broken wire on the ignition lock cylinder.


How do you change the ignition key on a 1991 Toyota Previa?

Turn the key to acc. and push the plunger in located on the Ignition lock housing


How do you change ignition switch on 97 ford expedition Eddie baur?

Do you mean the electrical ignition switch or the cylinder lock and key..?


In a 89 mercury grand marquis how do you ignition cylinder replacement?

how to change igntion lock


How do you get the ignition out of the housing in a 1984 Camaro?

Remove the steering wheel, the snap ring and plate, the signal light switch, and you will find the bolt that holds the lock cylinder


How do you change the ignition lock on an 86 Chevy Silverado?

Answerput your ignition key in the lock turnit to accesory, there will be a small pinhole you will have to stick a pin of some sort in there and then it should just pop right out.


How do you remove the key from the lock ignition?

1996 rodeo- how to remove key from lock ignition?


How do you replace an ignition lock cylinder on a Chevy S-10?

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.


How do you remove and replace an ignition lock cylinder on a 1994 Ford Bronco?

Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.


Have replaced the lock cylinder on a 1979 camaro and it still won't return to the lock position?

Then the rods that connect to it must be messed up, lubricate everything inside the door as they must be frozen up from rust.


How do you change the ignition lock cylinder in a 1998 ford explorer with no keys?

I'm wondering if a locksmith is capable of getting your ignition lock cylinder to rotate to the on/run position so the ignition lock cylinder release can be depressed to remove it ? I'm also wonderering what they would charge for that service, because I was charged $30.00 and taxes to open my door lock on my house.


How can you change ignition lock on 1991 ford explorer with no keys?

I'm wondering if a locksmith is capable of rotating the ignition lock cylinder to the on/run position so the release can be depressed to remove the ignition lock cylinder, or if a locksmith can make an ignition key for the existing cylinder ? I'm also wondering what it would cost. I was charged $30.00 and taxes to come to my house and unlock my doorknob lock this year. Something to check out.


How do you change a ignition lock on a 1994 Saturn SC1?

http://youtube.com/watch?v=D3o4IuScZZI


How do you change ignition lock piaggio zip4t50?

there is a little green ignition switch, this is whats used to turn engine on and off. a metal block goes onto this and then the actual lock barrel goes onto here


How do i replace the ignition lock cylinder on 96 silverado?

Begin by removing the retaining ring at the top of your 1996 Chevrolet Silverado ignition lock cylinder. Slide the ignition lock out and remove the wiring harness. Reverse the process to install your new ignition lock cylinder.


How do you change the ignition switch on a 2004 gmc 1500 sierra truck?

how to remove cover to replace ignition lock cylinder and what type of tools do i need


How do you change ignition on 93 Ford Taurus?

Ignition what?CoilControl moduleSwitchLock cylinderSee "Related Questions" below for more


How do you replace ignition lock 1999 vw beetle?

how to replace ignition lock for 1999 vw beetle