Best Answer

I suggest that you take it to the garage since you can deploy the air bag accidentally.

1990 with airbags?

My 1990 does not have an airbag. I suggest removing the steering wheel. Then remove the turn signal assembly. There should be 1 or 2 screws holding the switch in place.

User Avatar

Wiki User

โˆ™ 2015-07-15 18:34:22
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: How do you change the ignition lock on a 1990 Chevy S10?
Write your answer...

Related Questions

How do you replace an ignition lock cylinder on a Chevy S-10?

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.

Do you have to take the steering wheel off to change a ignition lock tumbler on a 96 Chevy Tahoe?


How do you install lock cylinder in 1986 Chevy truck?

Ignition Lock? or Door Lock?

How do you change the ignition lock on an 86 Chevy Silverado?

Answerput your ignition key in the lock turnit to accesory, there will be a small pinhole you will have to stick a pin of some sort in there and then it should just pop right out.

How do you change an ignition switch on a 1990 Cadallic?

you have to go under the dash and take out the steering column. and the ignition switch should have a wire going down to the bottom of the column coming from the ignition lock.

What do you do when the Key won't turn the in dash ignition on a 1999 grand am se?

change the Ignition Lock lock switch

How do you change the ignition lock cylinder in a 1989 Chevy Cheyenne when there is a key broke off in the ignition and it won't turn?

A locksmith may be able to remove the broke key and make a new one. Or just replace the ignition.

Change ignition lock on 1970 ford maverick?

How do I replace an Ignition in a 1970 Maverick

How do you install the ignition lock cylinder on a 84 Chevy blazer?

You will need to attach the wiring harness to the end of your 1984 Chevrolet Blazer ignition lock cylinder. Slide the cylinder into the cylinder slot. Secure the ignition lock cylinder with the retaining ring.

Where is the passlock sensor located on a 99' Chevy 2500?

Ignition lock cylinder

How do you change the ignition lock cylinder in a 2001 Chevrolet Tracker?

To change the ignition lock cylinder in a 2001 Chevrolet Tracker, first disarm the air bag system. Then remove the clock spring assembly to be able to remove the old ignition lock cylinder and replace with a new.

How do you change the ign key lock on a 1988 Chevy Celebrity?

To change the ignition key lock you have to: 1. Pull the steering wheel off. 2. Remove the lock plate. 3. Remove the turn signal switch. 4. Remove the set of contacts. 5. Remove the retainer bolt. The lock will then pull out of the housing.

How do you remove the ignition switch on a 1971 Chevy blazer without a key?

You would have to drill out the center of the lock or have a locksmith pick the lock.

How do you remove the ignition lock on a 1973 Chevy Corvette?

To remove the igniton lock, remove the steering wheel and turn signal switch housing. From there you will be able to see the lock which holds the ignition lock into place. slide a screwdriver into the slot and apply pressure. The igntion lock can then be pulled out.

How do you remove the Ignition Key Lock Cylinder to replace it on a 1976 Chevy Blazer?

this site will help

Do you need to change the key chip if you change the ignition switch in a terrano?

The ignition switch should be separate from the ignition key/lock assembly, so I'll say no.

How do you lock the steering wheel on a 1997 Chevy Malibu?

The wheel should lock when you take the key out of the ignition. If it doesn't, there's something wrong.

How do you get a key code or change ignition for a 1990 Mercury Sable?

Your Ford/Mercury dealer can get the code. See "Related Questions" below for instructions on changing the lock cylinder

Can a locksmith change an ignition lock set?

On most cars, yes.

How do you replace ignition lock cylinder on a 2004 Chevy aveo?

I broke my key in the ignition and cant get it out. My only option I can see, is to replace to tumbler. How do I remove it?

How do you install ignition lock in 2003 Chevy S10 pickup?

go to a repair shop they'll tell you

How do you remove the ignition lock cylinder on a 1964 Chevy puck up truck?

Turn it, then pull up and out.

Where is the ignition switch on a 1990 bronco xlt located?

The ignition lock is where you put the key. The ignition switch is located on the top of the steering column directly above the brake pedal.

How can you remove the Ignition lock cylinder from an 06 Chevy hhr with no keys?

you can use the car blank key to open it.

How do you remove a lock cylinder from a ignition swith without a key on a 1965 Chevy?

Without the key you are going to have to drill it out.