answersLogoWhite

0

  • Starters and Ignition Systems
  • Ford Expedition Eddie Bauer
  • Ford F-150

How do you change the ignition switch in a 1993 Ford 150 truck?

User Avatar

Wiki User

βˆ™ 2015-07-15 18:36:16

Best Answer
Copy

Insert the key and turn to the RUN position. There is a small hole in the steering column below the ignition switch. Insert a 1/8" drill bit (or something similar size) and push upward on the retaining pin in the hole. As you do this, pull out the cylinder lock. It should come right out. To reinstall, turn the new cylinder to the RUN position. Again depress the retaining pin and insert the switch into the steering column. Make sure the new switch is completely seated & aligned before you turn to the OFF position. This will let the retaining pin extend into the hole.

2015-07-15 18:36:16
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...
Still have questions?
imp

Related Questions

How do you replace an ignition switch in a 1993 infinity J30?

change switch


How do you change the ignition switch in a 1993 vandura 2500?

Begin by removing the retaining ring at the top of your ignition switch. The ignition switch will slide out. Remove the wiring harness from the end of the ignition switch. Reverse the process to install your new ignition switch.


Replace ignition switch for 1993 Buick century?

Replace ignition switch for 1993 buick century?


How do you change the ignition switch on a 93 Nissan quest?

Begin by removing the retaining ring at the top of your 1993 Nissan Quest ignition switch. Slide the ignition barrel out. Remove the wiring harness from the end of the ignition barrel. Reverse the process to install your new ignition switch.


How do you replace the ignition switch on your 1993 Chevy K 2500?

Remove the retaining ring at the top of your 1993 Chevrolet K 2500 ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.


How would you know if a fuel relay is blown in a 1993 subaru impreza?

you cant does it click when you switch on ignition if not change it.


How do you replace the ignition in a 1993 Chevy Lumina?

IGNITION ? ARE we talking ignition coil-ignition wires ignition switch-key & tumbler.


1993 f250 4x4 we have already replaced the ignition switch and the key will turn the truck over but will not shut it offThe switch feels loose or free no retention any ideas?

adjust the rod that goes from the switch/key (runs on top of the column) To the switch at the base of the column !! Switch at the base is adjustable !!!


Where is the ignition switch located on 1993 Taurus?

On the right side of the steering wheel.


How do you replace a 1993 Corvette headlight dimmer switch?

How do I change the dimmer switch on my 1993 corvette?


How do you change an ignition switch on a 1993 Chevy S10 Blazer?

youve got to remove the steering wheel, take the locking mecanism off, then the mecanism for the signal lights off....whitch should only have a few screws.....then where the ignition switch is.....you should see a screw that looks like it goes through the switch..remove that then give the ignition switch a tug or two and it should come out


Where you can get the ignition switch for ford escort station wagon 1993?

Most major parts houses would have the ignition switch. Any year between 1991 and 1996 will fit it.


Does a 1993 Chevy S10 pickup truck have an inertia switch?

No it does not. That is a Ford thing.


Why will a truck not unlock the steering wheel and start on a 1993 Toyota 4WD pick up?

The Lock Is Bad, Everyone Calls It The Ignition Switch. The Switch Is Actually Pushed On By The Lock When You Turn You Key By Way Of A Small Rod. Your (lock) Ignition Is Hanging. Give The Sterring Wheel A Couple Hard Turns Might Work.


How do you change an ignition module in a 1993 Chevy blazer?

your a fatty


How do you replace the ignition switch on a 1993 Pontiac Grand Am?

It's really easy the switch is in the steering colume.


Your 1993 Ford Escort won't shut off when the key is turned off I unplugged the ignition switch in the steering column - not it I then replaced the starter relay under the dash Didn't help either?

your key switch may be bad. There is a little shaft that gets weak and breaks in your ignition switch. you can check it by removing the plug to the switch on the left side, check to see if the little shaft is broke. If so you have to change the ignition switch. (key switch.) good luck.


What can cause the turn signals not to work on a 1993 Chrysler LeBaron?

Fuse, flasher, switch, bulbs, wires, ignition not on, dead battery,Fuse, flasher, switch, bulbs, wires, ignition not on, dead battery,


How do you fix a wiper switch on a 1993 Dodge Dynasty?

change wiper switch


Are ignition switch and lock cylinder 2 different parts on 1993 Dodge Dakota?

Yes. The lock cylinder is metal part that the key goes into. The ignition switch houses the lock cylinder.


How do you remove the Ignition switch assembly on a 1993 Acura Legend?

you have to replace the whole steering column


Will the ignition switch cause your 1993 mercury villager fuel pump not to work?

No, there is no direct connection.


How do you change clutch 1993 Nissan Pickup?

Show us a video on how to change a clutch on a 1993 Nissan pickup truck.


If a 1993 corolla chimes as if the key is in the ignition and the drivers door is open only there is no kew in the ignition what could be the problem?

MY GUESS IS A FAULTY IGNIGION SWITCH.


What to do to get the security light off the 1993 buick park avenue?

turn ignition on leave it on for 10 minutes then switch ignition off then you start the car