answersLogoWhite

0


Best Answer
Copy

You need to remove the dash panel underneath the steering column. You will find the switch attached to the left side of the column with two 5/16" or 8mm screws. If you are sure it is the switch, you can go ahead and buy one so you know what it looks like, and know what to look for under the dash.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:52:44
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you change the ignition switch on a 1986 Camaro?
Write your answer...
Submit

Related Questions

Where is fuel pump reset switch on a 1986 Camaro?

Where is fuel pump reset switch on a 1986 camaro?


How do you install an ignition switch on a 1986 Chevrolet caprice?

Attach the wiring harness to the and of your 1986 Chevrolet Caprice ignition switch. Slide the ignition switch into the ignition slot. Tighten the ignition switch with the retaining ring.


How do you replace the ignition switch in a 1986 Ford 350?

Remove the retaining ring at the top of your 1986 Ford 350 ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.


How doi remove ignition without key from 1986 Toyota pickup truck?

Begin by removing the retaining ring at the top of your 1986 Toyota pickup truck ignition switch. The ignition switch will slide out. Remove the wiring harness from the back of the ignition switch.


Where is the ignition switch located on a 1986 Nissan 300ZX?

when you start the car up that's your ignition switch is located...


How do you change an ignition switch on a 1986 ford F150?

The ignition switch is usually mounted to the steering column and is operated by a linkage rod. NOTEOn column-mounted ignition switches, don't confuse the switch with the lock cylinder and keys. The ignition switch is not normally visible. On some vehicles, the steering column support has to be removed and the column lowered to find the ignition switch. On others, the switch is accessible under the dash.The ignition switch is operated by the key switch. Courtesy of Ford Motor Company. To replace the switch: * Remove the ignition switch wiring harness. * Unbolt it from its position. * Bolt the new switch into position. * Attach the witing harness.


Where is the fuse box on 1986 Chevy Camaro Z28?

where is the fuse box in a 1986 camaro


Where is the ignition starter switch located on a 1986 Lincoln town car?

On a 1986 Lincoln town car, the ignition starter switch is located near the bottom of the steering column. It has a rod going into it that operates it from the key lock assembly.Ê


1986 bronco switch ignition location?

On steering column behind lower cover.


How do you set the clock on 1986 Chevrolet S10 pickup?

Turn radio off. Turn ignition switch on. (engine not running). Pull OUT seek button to change hours. Pull out scan button to change minutes.


How do you remove the ignition switch from a 1986 Buick?

remove the steering wheel with special tools and then the turn signal arm and switch assembly plate to expose the ignition switch lock bolt use some fingernail polish to mark the positions of anything you remove.


Does a 1986 camaro have a governor?

no.


Will a 1986 Camaro 2.8 work in 1987 2.8 Camaro?

Yes


How much will it cost to have a replacement ignition key made for a 1986 Chevy Camaro Z28?

i went to the gm dealership and they quoted me at $45 because of the chip on the key


How do you replace ignition switch on 1986 GMC sierra pickup?

pulled steering wheel still cant get plastic cover off to acess switch any help


You turn the ignition on for a 1986 gmc truck and get no sound?

Engine Seized? Dead Battery? Loose or corroded battery cables Bad starter? Bad starter solenoid? Bad neutral or clutch safety switch? Bad ignition switch?


Does a 2002 Camaro have the same lug pattern as a 1986 Camaro?

Simple answer- NO Tech JK ----------


How do you change your high beam switch on a 1986 Mercury Topaz?

Just take the covers off the steering column, switch is there.


How do you replace the ignition switch on a 1986 Chevrolet Celebrity?

If you want to change the SWITCH, it is on the steering column about 18 inches above the floor. If you want to change the lock cylinder you need to remove the steering wheel, then the lock plate then the turn signal switch then the key reminder switch {the two little copper contacts} and you will see a screw that has a different head that goes through the edge of the cylinder. Take the screw out then pull the lock cylinder out.


Why is my Tach not working on my 1986 Camaro after removing the ignition coil and reinstalling it?

There is a wire next to the large (red) battery wire that is for the tachometer. Check to see if you plugged it back in and is the connection good.


Where is the crank sensor location on a 1986 Camaro z28?

There is no crank sensor on a 1986 camaro z28.. that sensor is in the camaros past 1988 i believe.. but the 1986 carb or fuel injection (tpi) does not have one


Will a stock 305 motor from a 1986 iroc fit into a 1995 Camaro rs?

Will a stock 305 motor from a 1986 iroc fit into a 1995 camaro rs?


How do you replace ignition switch on 1986 camaro?

Remove the dress plate under the steering column. There is a clip there for the shift indicator, if you shift on the column. There are two nuts on studs, one on each side of the column, remove these nuts, and the steering column will drop down. The switch is on top of the column just lower then the fastening bracket. Unplug the wiring, remove the screws that retain the switch, install new one and adjust. Put everything back together.


Will interior dash out of 1986 Camaro fit a 1977 Camaro?

No, they're from 2 totally different bodystyles


Can a under hood wiring harness from a 1986 Pontiac plug in to a 1989 camaro?

I doubt it very much as they change electronics about every year.