Top Answer
User Avatar
Wiki User
Answered 2011-09-13 00:23:51

first go to your local hardware store and pick up the largest sluge hammer you can find! Then smash the lense until the light bulb is exposed or smashed its self and then change the bulb! Lastly find the pieces from the broken lense and Duct Tape it back together! hope this helped!!!

User Avatar

Your Answer


Still Have Questions?

Related Questions

Chevy s10 fwd light will not come on?

The bulb may be blown. Replace the bulb.

Do it yourself oil change on 1996 Chevrolet S10?

Yes, there is no reason you should not be able to change the oil by yourself in a 1996 Chevrolet S10.

How do you change a signal light on a 2000 s10?

Assuming this is a front signal light you are trying to replace, you need to remove the head light assembly first. This will give you room to access the signal light bulb.

How do you remove the tail light cover on a 2003 S10 so you can change the bulb?

There are two Philips screws inside the bed. Lower the tailgate and you can see them...

How do you replace bulb tail light in 99 Chevy S10 Extreme?

u have to to take the lens off the light

How do you remove the plastic cover to change the rear tail light on a 1997 Chevy S10?

the cover does not come off, you must remove the entire light assembly and remove the bulb from the back side

What is the correct light bulb for a 1993 S10 Chevy blazer rear turn signal?

2057 bulb you can find it cheap at walmart.

How do you remove the tail light lens cover 1996 Chevrolet S10?

Open your tailgate and there should be two screws. Your owner's manual should describe this procedure too. If you are replacing a bulb, see sources and related links below for bulb information.

How do you change a Chevy s10 back turn light?

You will need to remove the tail light assembly to gain access to the bulbs. Open the tail gate and remove the two small screws that hold the tail light assembly in place, then wiggle the tail light assembly out in the open. Now you can unlock and twist the bulb socket out to replace the blown bulb.

On 97 s10 left blinker flasher makes fast sound but no light?

Check the bulb, it could be blown.

How do you change a headline in a 1996 blazer s10?

The head lt. bulb is located on the back side of the lense. raise the hood look on the back side, you'll see a large ring twist it counter clockwise, pull the bulb out and unplug it from the adapter. When you reinstall the new bulb do not touch it with youre fingers, the oil from you're skin will shorten the life of the bulb.

How do you change a brake light on a 1997 extended cab Chevy S10 pickup truck?

Open the tail gate, remove two small screws that hold the tail light assembly in place, wiggle the tail light assembly out, twist out socket and replace the bulb.

How do you change a cabin filter 1996 Chevy s10 truck?

I don't believe they had a cabin filter.

Why does your brake light fuse keep blowing on your 1997 Chevy s10?

Your bulb or socket may be shorting out. Check for shorts in the system.

How do you get out the third tail light in a 95 s10?

Remove the two screws holding in the lense, remove the lense, remove the bulb(s).

Why is the service engine light on your 1991 S10 Chevy blazer?

time for an oil change

Amount of oil for a 1996 Chevy s10 pickup?

Engine oil, 4.5 qts with filter change.

How do you change oil sensor on 1996 Chevy s10?

If that S10 has a 4.3 engine, I find it best to remove the distributor to gain better access to the oil pressure sensor.

How do you disable the air bag on a 1996 Chevy s10?

You can pull the fuse to disable it but the air bag light will remain on.

Does a s10 1996 4.3 engine fit in 1998 s10?

check your answer

Will 1996 Chevy s10 transmission fit in a 2002 s10?


No dome light wiringfusebulb bulb holder and door switches ok on 1998 Chevy S10 Where do you look next?

Be sure the dome light override switch is turned off.

Will the windshield off a 1996 s10 cab fit on a 1998 s10 cab?

yes the s10s were the same from 94 to 04 exept for the interior and grill change in 1997-1998

How do you replace a 2003 Chevy S10 license plate light?

twist rubber housing a quarter turn pull out replace with new bulb

What would cause the third brake light not to work but the other brake lights do in a 1994 s10 pickup?

a blown bulb or loose wire.