answersLogoWhite

0


Best Answer
Copy

1. Open trunck/liftgate 2. Remove the top screw holding the tailight housing cover to the body. 4. Remove the black plastic tailight housing covers. (They have snaps holding them in place) 3. Slide/Shift the left sided tailight housing to the left, vise-versa if removing the right. Dont be afraid to use a bit of force, they will slide out. 5. Rotate the bulb holder 1/8-turn counter clockwise and pull it out of the housing.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:55:02
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you change the stop light bulb on a 1993 Ford Probe?
Write your answer...
Submit

Related Questions

How do you remove rear brake lens on 1993 ford probe?

The 1993 Ford Probe rear brake light lens cannot be removed. The tail light are a complete seal light. The light bulb's can be removed from the rear of the light assembly.


Dia gram of starter location 1993 ford probe?

diagram of starter in a 1993 ford probe


Factory rim width on 1993 Ford Probe gt?

ford probe gt rims are 7 inch


How do you change the axle in a 1985 ford probe?

THERE WAS NO FORD PROBE IN MODEL YEAR 1985


Where do you locate the fuel pump on a 93 Ford Probe?

Were do I locate the fuel filter on a 1993 Ford probe 4 cylinder


1993 Ford Probe has the OD light flashing and a thump when it shifts between gears What is wrong with it?

pulse generator is bad


Will rims from a 1993 Ford Probe fit a 1996 Ford Mustang?

Not directly, no.


What do you have to do to change a fuel pump on a ford 1993 probe the engine is a 2.0?

Remove fuel tank Remove fuel tank


What engine is in Ford Probe?

its a Mazda engine . ( DOHC 4cyl. 16 valve 2.0l ) For the probe 1993


How much hp does a 1993 Ford Probe 2.0 have?

115 horsepower


Will the engine and transmission of a 1995 Ford Probe fit into a 1993 Ford Probe?

Yes,but the 93 and 94 enginges are obd1,while the 95-97 are obd2.


How do you change a 1993 Ford Ranger clutch?

how to i change a clutch in a 1993 ford ranger


Where do you add the transmission fluid in a 1993 Ford Probe?

Same place you check it.


Where is the fuel pump on a 1993 Ford Probe?

it is located inside the fuel tank


What are the back speaker size for 1993 ford probe?

6 X 9


Where is the fuel pump located on a 1993 Ford Probe GT?

in the fuel tank


How do you hook up the Sleepy Eye Modification on a 1993 Ford Probe GT?

---- ---- == == ---- == == ---- == == ---- == == ---- ---- == == ---- == == == == == == == == == == == == == == == == ----


How much did a 93 Ford Probe cost new?

Brand New 1993 Ford Probe right off the show room floor cost me "$29 800.00"


Where is the coil on a 1993 Ford Probe gt?

On the '93-'97 GT's the ignition coil is part of the distributor. If your coil goes bad you need to change the distributor.


Where is the idle adjustment screw located on a 1993 Ford Probe?

its located on the throttle body


Where is the transmission dipstick for a 1993 Ford Probe 2 liter?

It is important to check and maintain the fluid levels while owning a car. The transmission dipstick of a 1993 Ford Probe is located behind the engine, to close to the firewall and it has a yellow cap.


Will a 1994 Ford Probe Alternator fit on a 1993 Ford Probe gt?

if the 94 probe is a GT, yes. the 2.0l alternators are different from the GT the autozone part numbers for the 94 2.0L Probe is 14449 and the part number for the 94 2.5L GT is 14450


Does a 1993 Ford Probe gt 2.5l have forged pistons?

they do not come stock with forged pistons, no probe gt does. You will have to buy them and install by yourself


Where is the oil filter located on a 1993 ford probe?

The 1993 Ford Probe oil filter can be found on the left side of the engine. The oil filter will be near the oil pan. The oil filter is easily seen from the bottom of the engine looking up.


How do you change oil pressure switch on ford probe gt?

o my