You fail to mention if it is a 4 cylinder or V6. On the 2.4 Liter 4 cylinder the firing order is 1-3-4-2. Standing in front of the car looking at the engine from left to right the cylinders are 1-2-3-4. On the 3.0 Liter V6 the firing order is 1-2-3-4-5-6. Standing in front of the car looking at the engine from on the cylinder head nearest the front of the car the cylinders are left to right 2-4-6 and the rear cylinder head nearest the windshield left to right is 1-3-5.
The firing order on a 2000 Mitsubishi Galant v6 3.0L is 1, 2, 3, 4, 5, 6. The number one cylinder is located closest to where the driver sits.
theres 2,balance shaft and timing belt.mine were $75 for both,i installed them.@ a shop if you can get it done for under $500 your getting a good deal
it depends on your engine: 1) 4G64/G (galant?) 3-7 before tdc 2) 4G64/L (lancer?) 2-8 before tdc
It is important to know the firing order of a car being driven. The 2000 Mitsubishi Galant engine firing order is 1-3-4-2.
4 8 3 7 2 6 1 5 Front of car.
in front of the cat sensor 2 is after the cat
on the 2.4 engine #1 cylinder is the first one on right side of car, passanger side first spark plug is cylinder #1,next you'll see a coil .under coil is plug #2. then plug #3 then another coil under it is plug# 4
On a Lincoln LS , 3.9 litre V8 engine : The engine cylinder locations are numbered : firewall 4 - 8 3 - 7 2 - 6 1 - 5 front of vehicle
Bank one refers to side where ! 1 cylinder is and the sensor 2 is the rearmost(at the converter outlet).
Trouble code P0175 means: System too rich (Bank 2)
It will have 2 as it is a V-6
In a 2000 Ford Taurus : firewall 1-----2-----3 4-----5-----6 front of vehicle > driver
you won't believe this but it is 1-2-3-4-5-6 on v-6 and 1-3-4-2 on four cylinder
pi r^2 h is used to determine the volume of a cylinder because when determing the area of a shape you first have to determine the area of the the base of the object and then multiply it by the height. The base of a cylinder is a circle and to find the area of a circle you use pi r^2 and hence the reason why pi r^2 is used to find the volume of the cylinder.
Example: Volume of Cylinder = 2 liters = 2000 c.c. Diameter = 20 cm thus Radius = 10 cm pi (r^2) h = 2000 3.141592654 (100) h = 2000 h = 2000 / (100pi) h = 6.366197724
The surface area of a closed cylinder is equal to (2 times the area of the base) plus (the height times the circumference of the base)
Six cylinder, 1-5-3-6-2-4. Four cylinder, 1-3-4-2.
The 2000 Ford Ranger firing order is 1-3-4-2. The number one cylinder is the one closest to the front.
Four cylinder, 1-3-4-2. Six cylinder, 1-2-3-4-5-6.
1) Have vehicle scanned to determine which cylinder is misfiring 2) Does vehicle have C.O.P. (coil on plug)? usually a bad ignition coil on that cylinder 3) Remove spark plug from that cylinder and do a compression test to determine if problem is internal to the engine (bad valve or ring).
Start at 1 1/2 turns from seat and adjust for best idle
Cylinder #2 Misfire
On a 2000 Mercury Sable the engine cylinder locations are numbered : firewall 1-----2-----3 4-----5-----6 front of vehicle > driver
cylinder #5 is in right back of engine. 1-3-5 is in back, 2-4-6 is in front.