answersLogoWhite

0


Best Answer

Deactivating/activating the belt minder feature

Read steps 1 - 9 thoroughly before proceeding with the

deactivation/activation programming procedure.

The Belt Minder feature can be deactivated/activated by performing the

following procedure:

Before following the procedure, make sure that:

² the parking brake is set

² the gearshift is in P (Park) (automatic transmission).

² the ignition switch is in the OFF position

² all vehicle doors are closed

² the driver's safety belt is unbuckled

² the parklamps/headlamps are in OFF position (If vehicle is equipped

with Autolamps, this will not affect the procedure.)

To reduce the risk of injury, do not deactivate/activate the Belt

Minder feature while driving the vehicle.

1. Turn the ignition switch to the RUN (or ON) position. (DO NOT

START THE ENGINE)

2. Wait until the safety belt warning light turns off. (Approximately 1

minute)

² Steps 3--5 must be completed within 60 seconds or the procedure will

have to be repeated.

3. Buckle then unbuckle the safety belt three times, ending with the

safety belt unbuckled. This can be done before or during Belt Minder

warning activation.

4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps.

5. Buckle then unbuckle the safety belt three times, ending with the

safety belt unbuckled.

² After step 5 the safety belt warning light will be turned on for three

seconds.

6. Within seven seconds of the safety belt warning light turning off,

buckle then unbuckle the safety belt.

² This will disable Belt Minder if it is currently enabled, or enable Belt

Minder if it is currently disabled.

7. Confirmation of disabling Belt Minder is provided by flashing the

safety belt warning light four times per second for three seconds.

8. Confirmation of enabling Belt Minder is provided by flashing the safety

belt warning light four times per second for three seconds, followed by

three seconds with the safety belt warning light off, then followed by

flashing the safety belt warning light four times per second for three

seconds again.

9. After receiving confirmation, the deactivation/activation procedure is

complete.

User Avatar

Wiki User

โˆ™ 2012-01-16 17:14:18
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you disable the seat belt alarm in a Ford Windstar?
Write your answer...
Submit
Related questions

How do you disable the seat belt alarm on E250 ford van?

Disable the seat belt alarm in a e250


How do you disable seatbelt alarm on a Ford F-150 2004?

How do I disable seat belt alarm for a Ford F150 2004


How do you disable seat belt chime 03 ford windstar?

Use the seat belt and buckle up.


How-To Disable A Ford Edge Seat-Belt Alarm?

Buckle up!


How do you disable the seat belt alarm in a 2002 ford escape?

Escape seatbelt alarm can be disabled by removing the seatbelt alarm fuse. This will disable the alarm, but it is not recommended to operate the vehicle this way.


How do you disable the seat belt alarm on a Chevy Colorado?

To disable the seat belt alarm on a Chevy Colorado, locate the alarm fuse. Pull out the fuse to disable the alarm.


How do you disable seat belt alarm for 2007 ford explorer?

Buckle up.


How do you disable the seat belt alarm on ford 2011 F-150?

Buckle up.


How do you disable the seat belt alarm in a 2006 Ford Crown Victoria?

Wear your seat belt, your car is trying to save your life!


Does the 2001 ford windstar have a timing belt or chain?

The 2001 3.8L Ford Windstar has a timing chain, not a belt.


How do I Disable seat belt alarm turn off 2006 Ford 500?

leave your seatbelt fastened at all times


2008 E350 seat belt alarm - how do you disable it?

Wear the seat Belt !


Cancel seat belt alarm disable vauxhall astra?

I find that fastening the seat belt disables the alarm immediately


How do you disable seat belt alarm on a Chevy Colorado?

You wear your seatbelt!


How do you disable the seat belt alarm in a 2006 Ford F 150?

Buy a old chevrolet only a dumb phuckin hillbilly would say that!


How do you disable the seat belt alarm in a 2001 Ford Crown Victoria?

There should be a wire coming out of the bottom of the seat belt receiver where it's bolted to the floor. Simply unplugging it should do the trick.


Does a 2003 ford windstar have a timing belt or chain?

The 3.8 liter V6 engine in a 2003 Ford Windstar has a timing CHAIN


How do you disable seat belt alram on 2008 ford?

Put on your seat belt.


How do you disable the seat belt alarm on a 2008 f 150?

take out the fuse for it


Belt and pulley schematics for a ford Windstar engine?

3.8litre


How do you disable the seat belt alarm on a 2008 suburban?

While it is possible to disable the alarm by going into the wiring of the vehicle, there areÊsimpler ways. You can purchase seat belt extenders and simply cut the ends off, or you could just buckle the seat belt before you sit in the seat.


How do you remove seat belt alarm?

A quick way to disable your seat belt alarm in 2 seconds or less without tools or experience! Go to your search engine and type in " Seat Belt Alarm Stop". You're gonna love it!


Does a 1996 ford windstar have an alternator belt or a serpentine belt.?

Serpentine belt See "Related Questions" below for more about Windstar serpentine belts - routing & installation information.


How do you disable the alarm for the seat belt on a 2011 Jeep compass?

wear the seat bealt


How do you disable Buick Lacrosse CXL seat belt alarm?

You must fasten your seatbelt

People also asked

How do you disable seat belt chime 03 ford windstar?

View results