I just did mine, because the handle is broken off the bolt. Remove the large screw at the back of the hole on the bottom for the clip. The whole works should separate from the stock. I don't know if this is the offical way, but it worked. Take the screw out of the trigger mechanism - mine had one screw and one pin - and let the piece with the long screw sticking into it slide forward a bit. There is room to get a screw driver between it and the receiver. Slide the screw driver in and pry the piece out a little. I guess it's the firing pin release. After it is out a little the bolt will slide out the back. I think I'm going to vee around the block the bolt handle goes through, put some tack welds around it and then mill around the block to square it up again. The hole stripped that the bolt screws into. It doesn't look like it was much to begin with. I never used this gun much because the bolt broke early on. Was cleaning out under the stairs and decided to try to fix it. It helps to have a nice mig welder and a milling machine at work.AnswerThat is like turning left three times when you can simply turn right.
Open the bolt, pull the bolt to the rear until it stops. Pull the trigger and the bolt will slide out of the receiver. The large knurled screw on the bottom of the stock is the takedown screw - you will find it is slotted for a coin. Loosen that and the barrelled action will come loose from the stock. No need to take it down further.
50 to 80 dollars
Numrich gun parts, look under Marlin/Glenfield parts list
your marlin/glenfield was made in 1974.
The Glenfield 25 was manufactured from 1979 through 1982. Some would suggest the Marlin Glenfield 25 was produced from 1972-1982. Regardless, the Glenfield name was cancelled in 1983. The rifle continued as the Marlin Model 25 until 2003, which then became the Marlin 925. Thousands were produced so YES it is common to find a Marlin-Glenfield Model 25. How many original matching Marlin scopes made it so far with the rifle however is another story. I have not seen many with the matching scope so this may be uncommon. The Model 25 is a robust and classic rifle. Enjoy :)
value marlin glenfield model 60 22 simi auto rifle
Your serial number indicates that your Marlin model 60 was made in the year 1971.
$359.00 to $890.00 us $
Your Glenfield model 60 was produced in 1989.
Model indicates a particular design by a particular maker. In the case of the Marlin/Glenfield Model 25 rifle, it is a bolt action rifle in caliber .22 Long Rifle. It has a 7 shot box type magazine. The Model 25M is in caliber .22 Magnum
There were two lengths used in that model over production. Fortunately, we carry both of them. email@example.com
Marlin Glenfield. http://www.marlinfirearms.com/About/History.aspx Marlin Glenfield http://www.marlinfirearms.com/About/History.aspx
Glenfield,which was made by Marlin Firearms Company made a bolt action .410ga shotgun from 1956-1965.This was the marlin model 59 which is the same shotgun as your Glenfield model 60.
Call Marlin Customer Service 800-544-8892. Place orders there. Part # 504046. Glenfield 20 is same as Marlin Model 780, except for the wood.
your glenfield was made in 1968.
The Glenfield 22 model 75 is the same as the Marlin 75. It was made for Sears and the parts probably can be obtained from Marlin In New Haven, Connecticut. This site has parts for the Glenfield model 75. http://www.gunpartscorp.com/ I have them. www.countrygunsmith.net
most likely it is. marlin (glenfield is marlin) began using micro-grove technology in 1953.
See if this helps http://stevespages.com/pdf/marlin_60.pdf
Your Glenfield model 25 was made in the year 1988.
straight from marlin
The Marlin model 925 22 long rifle, was first introduced in 2003. Before that it was Glenfield Marlin model 25 or just Marlin model 25. Hope this helps.
200-300 dollars,depending on the overall condition and a good bore.