answersLogoWhite

0


Best Answer

I belive that there is a small hole on top or on the side if so push a small wire in it and pull on the lock at the seme time. In some cases you may have to turn the switch to the ACC side with the key while pushing the small wire (paper clip) into the hole, once you do that the switch should pull out.

User Avatar

Wiki User

โˆ™ 2007-03-20 07:23:19
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you disconnect the ignition lock on a 1967 El Camino?
Write your answer...
Submit
Related questions

How do you remove the ignition lock cylinder from a 1996 Ford Thunderbird?

Disconnect batter ground cable. Remove the upper and lower steering column shrouds. Remove lock screw and disconnect ignition switch electrical connector. Rotate the ignition switch to the RUN position. Remove the two screws retaining ignition switch. Disengage ignition switch from the actuator. When installing new key set, ensure new key set is in the RUN position prior to installion.


How do you remove a lock cylinder for a 1988 gmc jimmy?

if it is the ignition lock cylinder, first disconnect the battery, you need to remove the steering wheel ,turn signal switch , etc, then you need to insert the ignition key into the lock cylinder, turn it to the run position,then pull the cylinder out, reverse the operation to install the cylinder,


How do you remove the key from the lock ignition?

1996 rodeo- how to remove key from lock ignition?


How do you replace an ignition lock cylinder on a Chevy S-10?

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.


How do you remove and replace an ignition lock cylinder on a 1994 Ford Bronco?

Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.


How do you remove the ignition switch from a 1988 Dodge Ram 50?

Ignition switch and lock cylinder removal 1988 Dodge Ram 50.Disconnect the negative battery cable from the battery.Remove the steering column cover to gain access to the ignition switch/lock cylinder.Using wire cutters, remove the cable band.Remove the bolts that hold the ignition switch/lock cylinder to the steering column.Unbolt and remove the key reminder switch and remove the switch lock cylinder from the steering column.


How do i replace the ignition lock cylinder on 96 silverado?

Begin by removing the retaining ring at the top of your 1996 Chevrolet Silverado ignition lock cylinder. Slide the ignition lock out and remove the wiring harness. Reverse the process to install your new ignition lock cylinder.


How do you replace ignition lock 1999 vw beetle?

how to replace ignition lock for 1999 vw beetle


How do you replace the ignition of a 1992 Lincoln Town Car?

To replace Ignition Switch, first you have to remove the old one. To do this you disconnect battery ground cable. Remove the upper steering column shroud by removing the five self-tapping screws. Remove tilt steering column lock lever, Remove lower steering column shroud, disconnect the ignition switch electrical connector, turn ignition switch lock cylinder to the "run" position, remove the two screws retaining ignition switch, and finally unhook the ignition switch from the actuator. Now to install the new one.Make sure that the ignition switch lock cylinder is in the "run" position. You can test for the "run" position by rotating the ignition switch lock cylinder approximately 90 degrees from the "lock" position. Hook up the ignition switch into the actuator. You might have to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes. Install retaining screws. Connect electrical connector to ignition switch. Connect battery ground cable. Check ignition switch for proper operation, including start and accessory positions. Also, make certain that the column is in the "locked" position. Then Install upper steering column shroud. Install the lower steering column shroud and tilt steering column lock lever.


What do you do when the Key won't turn the in dash ignition on a 1999 grand am se?

change the Ignition Lock lock switch


How do you remove ignition lock cylinder from a 2000 ML430?

Remove the retaining ring from the top of your 2000 Mercedes-Benz ignition lock cylinder. Slide the ignition lock cylinder out and remove the wiring harness.


Do you need to remove the ignition lock to replace the ignition switch on a 94 Honda Accord LX?

no the switch can be independly remove from the back side of the ignition lock


How do you takeout old ignition lock?

look at the column around the ignition lock their is a set screw you must loosen and lock along with barrel will slide rite out.


How do you remove the ignition lock cylinder on a 1997 astro van?

Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.


How do you install ignition lock cylinder in a 94 Pontiac Bonneville?

Attach the wiring harness to the end of the ignition lock cylinder. Slide the ignition lock cylinder into the slot. Tighten the retaining ring at the top of the cylinder.


How do you install lock cylinder in 1986 Chevy truck?

Ignition Lock? or Door Lock?


How do you remove ignition lock key without key?

Removing a ignition lock cylinder from a 2002 ford windstar with no key


How do you remove ignition lock?

with your cox


How do you know if ignition switch is in lock position?

the steering wheel will lock and the key will come out, unless of course the ignition cylinder is broken


Ignition lock cylinder removal on a 94 ford escort?

How to remove and replace ignition lock on 94 escort lx wagon1.9


Why is ignition switch on 1991 ford explorer hard to turn with key?

Try lubricating it with some graphite powder and see if that helps. Spray it directly into the key opening. You may also have a key that is worn badly and needs replacing.Ignition lock cylinder hard to turnYour probably refering to the ignition lock cylinder. The ignition switch is behind your instrument panel. If your ignition lock is hard to turn try spraying some wd40 inside the lock. If this does not work have ignition lock replaced it is worn.


How DO YOU program a 2008 Chevy uplander key fob?

1. Close the vehicle doors.2. Turn OFF the ignition.3. Remove the key from the ignition.4. Press and hold the driver side door lock switch in the UNLOCK position.5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).10. Perform the previous step to program up to four transmitters (including your old ones).11. Remove the ignition key in order to exit the Program Mode


How do you change an ignition switch in a 2002 Hyundai Elantra?

1. Disconnect negative battery cable 2. Remove the steering column covers and lower instrument panel cover 3. To remove the electrical portion of the ignition switch follow the harness back and disconnect the electrical connector then remove the screw and detach the switch from lock cylinder housing 4. Lower the steering column 5. The switch/lock cylinder housing is clamped to steering column by shearhead bolts. Use a chisel and hammer to tap the bolts in a counterclockwise direction to unscrew them 6. Remove the lock cylinder/ignition switch assembly from the steering column


What does an ignition switch do for a 1997 jeep?

It engages and disengages the lock that starts the vehicle. There are 2 parts to the switch. The ignition switch and the lock assembly.


How do you replace ignition lock cylinder on a 1996 Mercury Tracer?

Begin by removing the retaining ring at the top of your 1996 Mercury Tracer ignition switch. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the cylinder. Reverse the process to install your new ignition lock cylinder.