answersLogoWhite
Chevy Blazer
Chevy Blazer S-10
Water Cycle

How do you do a drive cycle a 1998 Chevy Blazer?

345

Top Answer
User Avatar
Wiki User
Answered
2008-01-08 18:50:58
2008-01-08 18:50:58

There is no drive trace as a whole, however, some monitor cycles are similar and may pass through simultaneouslyCatalyst moniotor: Pre-req: no codes present, IAT between -4 and 176 deg f; ECT is avove 75 deg f; barometric pressure above 72kPa, STFT between -20% and 20 % -Idle vehicle 5 minutes until it is in closed loop -drive 5 min at steady speed above 50 mph -idle 2 min in drive (auto) or neutral (manual) *very stable idle is required to pass this monitor EGR Monitor: Pre-req: no codes present, ECT is avove 75 deg f; barometric pressure above 72kPa 1. Idle vehicle 5 minutes until it is in closed loop 2. Accelerate and drive for 1 min at steady speed above 50 mph 3. coast vehicle down to 20 mph (vehicle in drive or w/ clutch engaged, brake off) 4. repeat steps 2 and 3 four times * the GM egr runs during the deceleration portion of the drive trace Evaporative Monitor:Pre-req: no codes present, IAT & ECT between 45 and 85 deg f: barometric pressure above 75 kPa, fuel tank level between 26 and 74 %; TPS between 9& 35 %; evap solenoid is at 50% pwm within 65 sec of engine run time -Idle vehicle 5 minutes until it is in closed loop -drive 5 min at steady speed between 30 and 40 mph -stop and idle 2 min O2 Sensor Monitor: Pre-req: no codes present, IAT above 32 deg f; ECT is avove 167 deg f -Idle vehicle 5 minutes until it is in closed loop -drive 3 min at steady speed above 50 mph -drive 2 min at steady 40 mph -drive 2 min at steady 50 mph

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


HOW TO GET A PULLEY OFF A 1998 CHEVY BLAZER


It is rear wheel drive, until you shift it into 4 wheel drive.


I need diagram for 1998 chevy blazer fuse panel


Will a 2000 blazer transmission fit a 1998 s 10 chevy 4x4 truck


Yes, you can put a 1998 4WD S10 drive-train on a 1997 Chevy Blazer. However, it will not be an easy process and will require a lot of work to get it installed correctly.



The fuel gauge fuse on 1998 Chevy blazer is located in the front of the blazer. It is on the driver side next to the hook latch.


NO it will not. They are complete DIFFERENT designs. Will NOT interchange.



1998 chevy blazer wont start good spark and good fuel presure


The oil cap on a 1998 Chevy Blazer is located on the passenger side of the motor. It is just to the left of the manifold cover.


The fuse box for the fuel gauge on 1998 Chevy blazer is located on the driver side. It is near the hook latch.


The oil pressure switch on a 1998 Chevy Blazer is on the side of the engine block. It is located above the oil filter.


1998 Chevrolet Blazer did not have vent windows.


When owning a car, a person should know the ins and outs of the vehicle. The 1998 Chevy Blazer does have the rack and pinion steering.?æ


The tire jack is located in the rear inside of your Chevy blazer. The jack can be found in a side compartment.


P235/70/R15Chevy Blazer 4WD 2DRwhat is the tallest tire i can put on this 1998 s-10 blazer without causing any problems? thank you


I'm sure it will, But you need to measure both of them first.




Check out this site http://www.nadaguides.com/


The transmission dipstick on a 1998 Blazer should be located at the rear of the engine. It should not be near the oil dipstick.


The ERG valve is located on the front of the engine on a 1998 Chevy Blazer V6 4.3L. It is near the top bolted to the intake manifold.


In most cases, you will find the speed shift sensor for your 1998 Chevy Blazer located on the backside of your transfer case. The transfer case is located on the transmission.


SEE OBD II drive cycle



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.