Geo Metro

How do you find an electrical wiring diagram for a 97 geo metro 4 door?

123

Top Answer
User Avatar
Wiki User
Answered
2009-06-14 11:19:59
2009-06-14 11:19:59

the electrical diagram is in the book... buy a service manual or a chilton's book

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


There is usually a wiring diagram/schematic on the inside of the blower/fan door.


Where can I find a passenger side door wiring diagram for a 1996 Honda civic ex coupe?


wiring diagram for 98 ford ranger door alarm


On the inside of the blower panel door.



A wiring diagram for the driver's door on a 1995 Jeep Grand Cherokee Limited can be ordered from the Jeep dealership. It can also be purchased at auto parts and major book stores.


Check in the wiring at the point where it comes into the door from under the dash. Alot of times, wires get pinched at this point.


Go to www.the12volt.com they will have diagram your looking for FREE..


To repair the wiring on the trucks door locks, you will have to find the problem first. Check all of the wires connectors for loose or bad connections, and look for any places in the wiring where the insulation has worn through.


Since the door contains no wiring it (a nail) should do no harm. A mirror will not affect the equipment within the room.


In a Haynes Manual. Used ones are often cheap on Amazon.


you might try haynes! they make the haynes auto repair manuals. i believe it is www.haynes .com


The best source for a wiring diagram is a good repair manual. There are repair manuals for your vehicle sold at most auto parts stores.


I do not have a diagram, but I was just curious if your having the issue where your driving and the i.c. says that the door is open? this is a common issue with these G500s. Most common is the door latch itself goes bad and needs to be replaced, but one thing I have also seen is: if the car has the illuminated door sills, and that relay goes bad, it can also cause the same complaint.....but if you do not have the illuminated door sills then its probably the latch. good luck with the diagram


There is an electrical problem with the switch or wiring. Have it checked out/


Go to the following website. It will show how to remove the door panel. http://www.kwmuth.com/techsupport/pdfs/21000280.pdf


No, there is not a diagram to take apart the outside of a door handle. However, there is a diagram that shows how a door is held together, and from there a person can take apart the outside door handle.


In the back of a Haynes repair manual or autozone.com there you will find online repair manual's


door latch diagram for 2000 Chevrolet silverado


This is caused by a defective or misaligned door ajar switch. You need to get a wiring diagram and verify open-closed switch function of each individual sensor. If you have the wiring diagram please post. You are not alone!Answerlook here -> http://www.cartrackers.com/Forums/live/fordwindstar/20.html


You would need to remove the inside panel of the door first to unplug the electrical wiring to the door. Then there are bolts on the hinges you can remove to take the door off. When you install the new door you wil need to adjust it so the latch meets up with the door jam.


There are several electrical wiring options available for a car alarm system. A person can have their car alarm wired so it will go off if anyone touches it. Also, a car can be wired to set an alarm off is anyone tries to open a door.


If you wait long enough the problem will not be intermittant anymore and you can fix it. Sounds like an electrical problem to me if they all are doing it and the problem should be in the driver's door. I would be looking at the wiring harness that goes through the rubber boot tween the door and the body....that's where the most flex in the wiring comes from.


You would need to remove the inside panel of the door first to unplug the electrical wiring to the door. Then there are bolts on the hinges you can remove to take the door off. When you install the new door you wil need to adjust it so the latch meets up with the door jam.


It is best to use the wiring diagram for the Mercedes 190 E to remove the panel door. You must use certain tools as well to remove the panel door such as a latch pin removal pliers and rivet head removal tool to remove the panel door.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.