Best Answer

You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.

User Avatar

Wiki User

โˆ™ 2004-11-22 22:16:13
This answer is:
User Avatar

Add your answer:

Earn +5 pts
Q: How do you find the cylinder head bolt torque sequence for a 1989 Chevy 350?
Write your answer...

Related Questions

What is bolting sequence and torque on a 1989 Chevy 350 intake manifold?

the sequence is the two center bolts on each side, the work your way outwards

What gas mileage does a 1989 Chevy s10 Tahoe 6 cylinder get?

what does a 1989 Chevy s10 Tahoe 6 cylinder get in gas mileage

What is the torque for cylinder head bolts BMW 325i 1989?

no bode no man

What are flywheel torque settings for 1989 Chevy 350?

75 Ft LBS.

Cylinder head torque spec for 1989 Chevrolet Cavalier?

need to know which engine you have

How much horsepower and torque does a stock 1989 Chevy truck have with a tbi 350?

its a chevy, so its too much for your mom and her

What is the torque specification for Toyota Camry 1989 four cylinder head bolts?

1991 toyota camry head bolts torque specs

What is the head bolt torque for 1989 mercury tracer 1.6 engine?

The 1989 Mercury Tracer 1.6 liter engine cylinder head bolt torque specification is 135 pounds. The cylinder head bolts should be torqued in 45 pound intervals.

What is the torque for the headbolts on a 1.6 liter motor on a 1989 Nissan Sentra 4-cylinder?

I have a 1.6 L motor, it was; torque to 21, then torque to between 51 and 54 lbs. completely loosen bolts then repeat tightening pattern above.

What are torque specs for 1989 Chevy 350 crankshaft bearing caps.?

60 ft lbs

What are the torque specs on a 1989 camaro RS oil pan?

Oil Pan torque on the small block Chevy V8 is 12 lb/ft.

How much horsepower and torque did a stock 1989 Chevy 6.2l diesel engine put out?

I believe 130 HP, and 240 FT/Lbs of torque.

What is the horsepower and the torque of a 1989 Chevy S10 Blazer 4.3L V6?

160 HP / 230 TQ

How do you bleed a clutch master and slave cylinder on an 1989 Chevy?

It is important to bleed a clutch master and slave cylinder to make sure all of the air is out of the lines. For a 1989 Chevy you would need to know model you had, and then find the repair manual for that specific vehicle.

How many cylinders does a 1989 Chevrolet Cavalier have?

The 1989 Chevy Cavalier could be either a 2.0L 4-cylinder or a 2.8L V-6.

What is the Cylinder head torque pattern in a 1989 dodge shadow?

45, 65, 65 ftlbs , 1/4 turn

1989 4 cylinder Plymouth Acclaim Cylinder head torque specifics diagram?

There are 10 bolts. Start with the center bolt on radiator side and work outward in a circular pattern. The torque steps are 45,65,65 ftlbs and then a 90 degree turn.

Were is the fuel pump located on a 1989 Chevy s10 truck 4 cylinder?

It may be in the fuel tank.

How many torque struts are on a 1989 Chevy Celebrity?

1or 2 holds up the hood or if wagon rear glass

What is the fluid capacity of a 1989 Chevy 700r Automatic transmission?

Including the torque converter, aprox 10 US qts.

Torque specs on a 1989 dodge shadow 2.2 cylinder head?

45, 65, 65 ftlbs , 1/4 turn

What is cylinder head torque for 89 Honda civic 1.5?

The 1989 Civic has a maximum torque rating of 97 pounds per foot at 3,000 RPM. 1989 was the first year Honda premier the more powerful 1.5 liter engine in the Civic.

What is the Head torque sequence Isuzu 1989 trooper 2.6?

First torque to 58 ft lb Second torque to 72 ft lb 1-10 in order. Front side on Left side 7,3,2,6,10 Right side 8,4,1,5,9 This is facing the engine.

Torque for the hub nut on a Chevy Celebrity wagon 1989 2.8 lt v6?

According to both my factory service manual and my Chilton manual the hub nut torque is 192 foot pounds.

What is the correct firing order for a 1989 Chevy S-10 pickup 2.5L 4-cylinder?

1-3-4-2 rotor turns clockwise.