answersLogoWhite

0


Best Answer

Try popping off the cover at the bottom of the wiper. There should be a 15mm sized nut(I think). Make sure this nut is tightened down good. If that doesnt work then the linkage has come undone.

User Avatar

Wiki User

โˆ™ 2007-03-12 22:54:19
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you fix the windshield wiper passenger side on a 2001 F150?
Write your answer...
Submit
Related questions

Where is the windshield wiper motor on a 1993 Ford F150?

top of the fire wall under the hood your wiper arms will connect


Why does driver side wiper work and the passenger side wiper doesn't on 2001 F150?

There'll be a linkage which connects the two wipers together... that may have come loose or gotten broken otherwise.


Where is the windshield wiper motor governor found on a 1990 Ford F150?

The governor for the wipers is located near the fuse box. It is wired to the harness going to the wiper switch.


How do you replace a windshield wiper motor for a 1998 f-150?

To replace a windshield wiper motor for a 1998 F150, first remove the bottom trim on the window. Then remove both wiper blade assemblies and all screws on the metal cowling. Remove the retaining clip from the wiper motor linkage and pull the controls rods off.


Windshield wipers not working 1998 ford f-150?

If the windshield wipers are not working in a 1998 Ford F150, the cause could be a blown fuse. There could also be a problem with the vacuum hoses connected to the wiper motor or the wiper motor itself.


What size Ford F-150 windshield wIper?

Wiper blade sizes will vary depending on the year of the Ford F150. See sources and related links below to look it up.


Where is the cabin air filter on a 2000 Ford F150 - if equipped?

It is under the coweling, passenger side below the windshield wiper. Some don't have a filter in them for what ever reason, so don't depend on looking for an old one to find the spot.


How do you replace a turn signal and windshield wiper assembly on a 1998 Ford F150 4x4 4.2 LT with AC?

Take it to a Ford Dealer.


What size is the windshield wiper blade for a 2001 F150?

The 2001 Ford F-150 takes 20" wiper blades on both sides front. See sources and related links below for more information. Since there are over 22 different wiper arm attachments, do not buy wipers just by length only - be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment.


How do you fix windshield wipers that wont move after they tried lifting snow on 99 Ford F150?

Your windshield wipers were most likely overloaded and blew the fuse, try replacing the fuse. If that does not fix it then it is possible that the wiper motor burned out and will require replacement.


Which is the 2 cylider on a 2001 f150 5.4?

passenger side of engine , second cylinder from front is the # 2 cylinder


Where is the fuel pump reset switch at on a 2001 v6 f150?

In the right front passenger footwell , by the kick panel


How do you replace windshield wiper motor on 1993 F150?

First, remove the windshield wipers. Then you can remove the cowel just in front of the windshield. There are a bunch of screws connecting it to the firewall. Once you remove this, close the hood. Now everything is easily accessible and the rest is intuitive. Replace everything by using the opposite procedure.


Location of turn signal flasher on 2001 ford f150?

On a 2001 Ford F150, the turn signal flasher is located in a relay box on the passenger's side of the steering column. To access it, you must remove the panel under the steering column.


Need a passenger front door handle for 2001 ford f150 harley Davidson edition?

Dealer or local junkyard.


Where is the windshield wiper motor on a 2003 ford f150?

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.


How do you change the windshield wiper motor on a 2002 Ford F150?

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.


How do you change wiper motor on 2002 ford F150?

Windshield Wiper Motor Removal & Installation Front 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor. To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFFposition to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.


Changed wiper motor and switch wiper still don't work on my 97 f150?

Check fuses and relays


How do you change the battery on a 2001 Ford F150?

How do you remove and replace the battery on a 2001 Ford F150?


How do you take off the windshield wipers on a 1993 F150?

The 1993 Ford F-150 has the most common hook-end wiper arms. See sources and related links below for installation videos. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.


How do you remove the wiper arms on a 1987 F150?

There is a C clip that holds them on.


Will 2001 ford f150 drivers door fit on 2001 expedition?

Yes, the 2001 Ford F150 driver's door will fit on the 2001 Ford Expedition.


Where is the vin located on a 1978 F150?

Drivers side, bottom of windshield.


How do you replace the wiper motor on a 1989 Ford F150?

First you have to remove the wiper arms. Then remove the cowl plate between the windshield and the hood (screws will be in the top of the plate and inside the hood). This will give you access to the back of the wiper motor. There you will find a clip holding the wiper arm mechanism to the motor shaft. Remove the clip and the arm mechanism. Now remove the connectors and take the nuts off the front of the wiper motor. It will pull off the firewall. Reverse procedure to install new one.