answersLogoWhite

0

  • Auto Parts and Repairs
  • Chevy Blazer S-10
  • Ford Ranger XLT
  • Pulleys

How do you get the camshaft pulley off?


Top Answer
User Avatar
Wiki User
Answered 2015-07-15 19:27:58

It depends on what you are working on. Some just slide off and some have to be pulled off with a puller.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

Where is top dead centre on camshaft pulley mk 2 vw golf gti?

The camshaft TDC mark is located on the camshaft side of the pulley wheel. When the mark is level with the front reinforcing strip on the camshaft cover the camshaft will be at TDC.


Does a camshaft pulley interchange with a 1990 Honda accord to a 1992 Honda accord?

Yes it does interchange. 1990-1993 Accords have the same camshaft pulley (or cog).


How do you move the power steering pump on a 2002 Chevy Malibu to get to the camshaft position sensor?

take the belt off, remove the three bolts by turning the pulley (there are three holes in it to see the bolts), then you can get to the camshaft sensor.


Where are the timing marks on a 1995 Escort 4-cylinder?

One is on the crankshaft pulley the other is on the camshaft pulley.


Do you need to remove camshaft pulley to get to distributor cap screws on 94 caprice?

Remove crankshaft pulley& ballance


Where are the timing marks on the cam and the crank located on a Toyota Camry 4cl 2.2?

The crankshaft itself has no marks, the crankshaft pulley has one, it's white color. The same is true for the camshaft, it has no marks. But the camshaft pulley has a hole in it. That hole must alighed with the mark behind the pulley and the crankshaft should alighed with its own mark and the camshaft in the same time.


Where is a pulley and belt used?

pulley an belt are used in driving camshaft,alternator,water pump,air pump, compressor in a car.


How do you set the timing on 2002 Kia Rio?

This is the procedure for installing the timing belt, and contains the info on where all marks need to be set for proper timing: Install : 1.Install tensioner pulley 2.Pull tensioner pulley to its furthest point and tighten lock bolt. 3.Check that timing mark on timing belt pulley is aligned with timing mark on engine http://msw.kiausa.com/data/manual/sh...G/lc3b620a.gif 4.Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate. http://msw.kiausa.com/data/manual/sh...G/lc3b620b.gif 5.Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that order. 6.Check that there is no looseness in belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys. 7.Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt. 8.Tighten tensioner pulley lock bolt to specified torque. Tightening torque:28~38 lb-ft (38~51 N


Where is camshaft pulley ignition timing location for 1992 Toyota Corolla?

where is camshalf pulley ignition timing location for 1992 Toyota corolla?


How do you find crankshaft sensor on Fiat marea?

It's behind one of the camshaft pulleys. Why would a CRANKSHAFT position sensor be behind a CAMSHAFT pulley ??


Do you turn camshaft pulley clockwise or counterclockwise to line up marks?

Always clockwise.


Where are timing marks on camshaft pulley of uno mia 1100?

On the cam pulley, and the back of the head are two marks that should be alligned 0762646447 after hours


What causes a stange noise when you start your Renault megane 2004 1.6?

camshaft dephaser pulley


Where are cam timing marks on a 2.2 Camry?

You can find it on the crankshaft pulley and there is a hole in the camshaft pulley which must be line up with the mark on the cylinder head at TDC.


How do you align the timing marks for a 2.2 liter Toyota engine?

Timing mark on the crankshaft pulley (mark should be at zero) must be aligned with the mark on the camshaft pulley (mark should be in the middle of the hole in the pulley).


How do you get a pulley off a 1998 Chevy Blazer?

HOW TO GET A PULLEY OFF A 1998 CHEVY BLAZER


What mark do you Aline on the cam on 2000 metro There is an E and An I And bothe have a white dot by them it is a 1.3L?

It is the "E". Make sure the pin in the camshaft is in the slot with the "E" if you remove the camshaft pulley.


Kia cam bolt torque?

This is for a 2000 Kia Sportage. Camshaft cap bolt 16 lb-ft Camshaft Pulley Lock Bolt 42 lb-ft


How do you take off a camshaft puller from a 1999 Hyundai tiburon?

how to take off a camshaft puller from a 1999 Hyundai Tiburon


What special tools are needed to replace a timing belt on a 2000 ford escort ZX2?

camshaft timing peg and a crankshaft alignment tool... I'm half way through doing mine and realizing you need to take the camshaft pulley off to get to the bottom gear for the timing belt, I'm still stuck on how to get it off, it says to use a strap wrench so I'm guessing for to hold the pulley while you remove the bolt... anyone ever acomplished this?


How do you set cam timing on a 92 miata?

You can set the camshaft timing on your automobile by lining up the timing marks. There will be timing marks on the front main pulley and timing marks on the camshaft.


Where is the location of camshaft censor 1997 f-250 7.3?

location of camshaft sensor is on the front of the block above the bottom pulley wheel. this is easiest accessed from underneath the vehicle


Which direction to turn to take camshaft bolte off from 1998 Lexus ls 400?

Take off camshaft seal bolts


How do you change vectra camshaft?

can u get a bushing for ur cam shaft pulley ? or do ya buy ful thing


Where is the camshaft position sensor located on a 1997 Buick Riviera?

the sensor is located behind the pulley for the water pump has one single 8mm bolt in it u need to remove pulley to get at it