On the bottom of the door there are two bolts, you have to remove them. You'll need a small flat head to wedge between the panel and the door so you can release the clips, BE CAREFUL! These are easy to break. Once you get all the clips released you'll see that the door is still attached in the center, you need to use the small flathead to wedge in the interior handle, where you grip the door to pull it shut or push it open. It wont look like the center piece pops out, but I assure you it does. Once that piece is off, there are two more bolts to remove. Make sure you keep track of them. Silver are for the door handle, gold for the bottom bolts. Disconnect the speaker wire, and push up on the door panel. Be gentle because the power window and locks are still connected by a wire. Once the panel slips off, disconnect the lock and window wires. There ya go.
However, theres a pretty tricky little metal panel after the door panel. If you get it off let me know.
Remove the door panel. Find the track, for the passage window, loosen the track and put the glass, back in track. Put the track, back in track, and tighten it down. Put your door panel back on, and your ready to go.
Begin by removing the inside door panel of your Kia. Remove the window track retaining clips. Put the window back on the window track. Secure the window with new window track retaining clips.
To set the power window back on track in a Ford Focus, you have to remove the door panel. Once you get in there, you will see the track that you will need to put the window back on.
You can put a manual rollup window back on track, in your 1994 Chevy Cavalier, by removing the inside door panel. The window track is easily visible with the door panel removed.
dissasemble the door by removing the door panel. You unbolt the window regulator and or window to reposition window or regulator to get it back on track. Most of the time something bends or breaks to cause a window to get off track.
Remove the inside door panel. The entire window mechanism will be visible. Put the window back onto the window track.
You will need to remove the inside door panel. With the door panel removed the entire window mechanism will be visible. Set the window back on the track and secure it with the retaining clips.
When a window goes off track on a 2004 Grand Am GT, the door panel has to be removed. The cable for the window is then reset on the track or repaired and the door panel put back on.
You will need to remove the inside door panel of your Chevrolet Blazer. Remove the window retaining clips. Put the window back into the window track. Tighten the window retaining clips.
Take door panel off. and put window back on track.
TAKE THE DOOR PANEL OFF FIRST
If a power window goes off track on a 1999 Camaro, the door panel can be removed and the window put back on the cable track. The door panel can be removed by opening the clips on the corners. If there are lights in the door panel, the light covers need to be removed first.
Remove the inside door panel of your 1999 Chrysler Intrepid. Remove the window retaining clips. Put the window back into the window track. Secure the window with the window retaining clips.
mY PASSENGER SIDE WINDOW CAME OFF THE TRACK AND YOU NEED TO TAKE OFF DOOR PANEL,REMOVE SPEAKER ,LOSSEN 1 BOLT THAT HOLDS THE TRACK (ABOVE SPEAKER) WINDOW SHOULD GO BACK IN SOME WHAT EASY.THEM TIGHTEN BOLT AND PUT PANEL BACK ON.
Realigning a window on a 2001 Pontiac Grand Prix requires the door panel to be removed. After the panel is off the window can easily be put back on track.
Remove the drivers side inside door panel. Remove the retaining clips from the window track. Place the new window in the window track and tighten the retaining clips.
How do I take the back panel off
Take the door panel off and put it back on the track
To put a window back on track in a 1996 Geo Metro, the door panel will have to be removed. Use a screwdriver to pry up the clips around the door panel. Then locate the window cable and rewind it. If the window is operated by a power switch, be careful not to pinch the fingers when rewinding the cable.
To put a driver's side window back on track on a Ford Expedition you will have to reseat the window. Do this by removing the door panel and putting the window back in place. You can use silicone or Gorilla glue to attach the window. Leave the window in the up position for at least one day once you have it back on place.
Take the inside door panel off and determine why the window came off track in the first place then make repairs/adjustments.
remove door panel and roll up window at the center of the door are two screws that dold the window to the motor remove them and carefully lower the window motor put window on track roll up motor and replace screws also check surrounding track screws and adjusment then replace door panel
open up the door panel which is a few screws and pull the door panel off, this will involve taking the speaker out aswell. on the bottom right hand corner of the door there will be a 10mm bolt that you will have to take out and that will release the bottom side of the track. from there just reach inside the door and put the window back inside the track and bolt the track back up. then put door panel back on.
take off inner door panel, lower track and put the window back in. If parts on track are broken buy new ones. Use urathain to reinstall window.
Type of vehicle would help, there are some different ways they work. In general, take the inside panel off. The front track is probably held in place by one or two bolts, top and bottom. You can usually take it loose, get the window in the back track and then the front. Sometimes the plastic rollers at the bottom of the window can break and this lets the window get out of the track. Something became out of line for the window to get out of the track.