answersLogoWhite

0


Best Answer

top of engine bay 2ft or longer extension 13mm swivel socket

User Avatar

Wiki User

โˆ™ 2008-11-19 17:55:11
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you get to the top bolt for a starter on a 1988 Mercury Cougar?
Write your answer...
Submit
Related questions

Do i need a 2 bolt or 4 bolt control arm for a Mercury Cougar?

I have a 1999 mercury cougar v6 2.5 liter engin and it needed a two bolt lower control arm on the passenger side


Is there a 3 bolt starter for a 1988 454?

NO Chevy did not make a 3 bolt starter. It only requires 2 bolts.


How do you remove alternator on 2000 cougar?

It should be the same as for a 2002 Mercury Cougar which is answered in WikiAnswer under the Question; " How to remove alternator from a 2002 Mercury Cougar 2.5L V6." The 2000 Cougar may be different by having an upper alternator BOLT. If it does, and you can't lift the bolt out (after fully loosening the bolt), lower the alternator and you can, then, lift the bolt out. When you begin to install the alternator (attach the power wire, and the wire connector) place the BOLT in the upper hole in the alternator, and THEN, raise the alternator to install.


Anyone know of a ground spot for 1999 Mercury cougar for amplifier?

trunk hinges or seat bolt


How do you replace motor mounts in a 97 Mercury Cougar?

Loosen the motor mount retaining bolt in your 1997 Mercury Cougar. Jack the engine up a few inches. Remove the retaining bolt and the motor mount bushing. Put the new bushing into the motor mount and reverse the process.


What is the wheel bolt pattern for a 2000 mercury cougar?

The 2000 Mercury Cougar (V6) came equipped in two tires sizes of 205/60/15 and 215/50/16. The offset and backspacing vary by wheel type (factory or aftermarket). The bolt pattern is 4-108 for this model.


Where is the starter of a 1986 Mercury Grand Marquis?

The starter is mounted on the passenger side of the transmission. It has one wire connected to it (with a small bolt) and there are two bolts holding the starter in.


What type of wrench is needed to remove caliper bolt on a 1999 Mercury Cougar?

I believe it's either a 40 or 45.


How do you remove a broken bolt from a 1988 Chevy truck k2500 starter?

Go to your local auto parts store and ask them for an easy out bolt extractor.


What is the wheel bolt pattern for a 1989 Mercury Cougar?

Hi there, it is 5-108 mm. Hope this helps...


How to replace starter on 1988 Ford F 150?

Disconnect the battery. Unhook the starter wires. Remove the two bolts on the starter. Take the starter out, and bolt the new one in. Reverse the procedure to finish the installation.


How do you fix a catalytic converter for a 1987 Mercury Cougar?

There is no way to fix a catalytic converter for a 1987 Mercury Cougar, since it is a sealed and unrepairable item. Once it goes bad, you must jack up the car, unbolt the old converter, then put a new one in its place and bolt it in.


How do you change the starter on a 1998 Mercury Grand Marquis?

Simply unbolt the old one and bolt the new one on, there is no trick to it.


How do you change starter on a 1988 Toyota Corolla sedan?

In the back of the engine one bolt is hidden under the air box


How do you change the starter on a 1988 Chevy Caprice Classic?

Disconnect the Caprices battery. Remove the wires from the starter, then unbolt the unit. Pull the starter out, then put the new one in the hole. Bolt up the new starter, connect the wiring, then reconnect the battery.


What size bolt patterns for aftermarket rims can you use on your 2001 Mercury Cougar ZN?

All '99-'02 cougars came with 4x108 bolt pattern. This is a bit of an odd ball size, but not too hard to find.


Where is the starter on a 1988 Nissan Maximum?

On the bottom of the transmission one nut one bolt make sure you remove the battery cable.


How do you replace the starter in a 1998 Plymouth neon?

are there 2 bolt ot 3 bolt on a starter on 1998 neon


What is the bolt size for a 97 Chevy cavalier starter?

The 1997 Chevy Cavalier starter bolt size is 9/16 by 3.5" inches long. You will need three starter bolts to secure the starter.


How do you replace a starter on 1988 Toyota supra?

when i did the clutch in my 1988 non turbo supra we had to take off the starter it was a pain it took us six hours just to get the one bolt off we tried using extension and everything we finaly got it off by going the inside of the car through where the gear shifter is put a couple extensions on it have one person hold it on the bolt and the other go at it with an impact driver by far the most difficult job i ve done on my car is that one starter bolt good luck


Do you need to remove the solenoid to access the top bolt on the starter of a 1992 Mercury Grand Marquis?

No...It will be a little difficult but you don't need to take the solenoid off.


How do you install a starter on a 1967 Corvette?

Bolt the starter into the starter position. There will be three starter retaining bolts. Connect the cables to the front of the starter.


Remove upper mounting bolt from starter on a 2002 Honda CRV?

(1) You must first remove the bracket clamp that retains the wiring harness to the trnsmission. (2) Disconnect the starter wires from the starter and that should give you the clearance you need to get a wrench on the upper starter bolt. (3) then remove the lower bolt.


Is there a shim in between the starter and the bolt holder on and 1989 Ford Ranger?

No there is not a shim between the starter and the bolt holder unless someone has put the wrong starter on and had to rig it up to make it engage properly.


Who is more famous Freddie Mercury or Usain Bolt?

Freedie Mercury