0
To get to an internal voltage regulator first disconnect the battery ground ( negative cable ) then remove the alternator. Make sure you mark the cables on the alternator so you can put them back exactly where they are supposed to go. The voltage regulator is inside the alternator and you will have to take it apart. I'm not sure how the regulator is mounted in your alternator, it might have small studs with nuts on them, or small screws or bolts, or it may be soldered in. In the latter case you will have to cut out the voltage regulator and solder in the new one. If you are going to take out the alternator anyway you should probably take it to a parts store where they will test it for free and tell you if you need a whole new alternator or just the voltage regulator.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you adjust and polarize the voltage regulator in a 1970 Ford?
A 1970 ford has a external regulator It's probably possible to adjust one by ajusting the contact points inside the regulator and I'm assuming it has a older style regulator but I don't think it will do much good. Replace the regulator. Disconnect the battery hook up the regulator hook battery up and boom it's polarized.
Do you need a voltage regulator if you hook up a 12 volt light to a 24 volt system?
Hook a 12 volt light to a 24 volt system and the light will burn out in seconds. You need a step-down voltage converter to do this.
How do you hook up a ford external voltage regulator?
Here is the proper hookup Voltage regulator teminal (I) goes to key switch Acc or Coil Risistor Voltage regulator teminal (A) goes to Alternator Battery Connection Voltage regulator teminal (S) goes to Alternator Stator Connection Voltage regulator teminal (F) goes to Alternator Field Connection Below is Incorrect. Hope this Helps. Ok this is the info that I have so far: (12VDC SYSTEM NEG GROUND) There should be multiple letters on the voltage regulator itself. The F goes onto the field post on the positive side of the alternator. The I goes to a fused + 12vdc (fuse panel) The A ? The S ? I think this goes to the switched "on" ignition point of the key. Any other valuable hints? F terminal on the regulator connects to the field connection on the alt. S terminal on regulator connects to the stator connection on alt. A terminal on regulator connects to the battery +( Plus) or positive terminal. (senses voltage of battery) I terminal on the regulator connects to the ignition switch. (turns regulator off & on) Caution do not connect I to spark coil +(positive) terminal,: may cause engine not to turn off.
Where is fuel pressure regulator on 05 ford f-150 5.4 v-8?
its part of the fuel rail has a vaccume line hook to it
Can you hook up a new regulator to an alternator without actually attaching it to the alternator?
Voltage regulators are often built into the alternators now, this wasn't always the case. Older vehicles had separate voltage regulators mounted on firewalls or the side of the engine compartment, wired in between from the alternator to the battery. The positive lead now goes directly to the battery from the alternator/regulator.
Does the electric fuel pump hook up to the voltage regulator on a 1966 dodge coronet 500 with a 440 motor that was put in it?
heavens no, you want to run a separate line to the fuse box for the pump through a relay.
How do you charge a battery using dynamo?
A "Dynamo" is a DC charger; these will overcharge any battery there is and requires a regulator circuit, they will produce voltage proportional to their rotation. Simply hook it to the battery (watch your positive and negative) and crank the generator / dynamo.
What is a palatal hook?
A palatal hook is a small hook for attaching elastic bands on the internal side of braces, or a term used in typography for a hacek.
Can you hook up a car seat to a 1999 ford expedition xlt?
Yes, you can hook up a car seat to the Ford Expedition
How do you hook up an tac in a ford ranger automatic?
you need to hook it up on the distributor
Installing a fuel pressure regulator into a 1998 GMC with a 5.7 engine upon removal of the old regulator and beginning to install the new regulator it says to hook the hose to the regulator upon remov?
Most of them are under the upper intake manifold but there is not a hose connected to it, point connection down
How do you install door glass 0n a 1970 challenger?
pull inside door panel off and look inside the door and unhook the glass from the regulator and pull the glass up out of the door, to reinstall drop new glass into door channels and hook to regulator by factory hook-ups.
