Quantcast
answersLogoWhite
notificationBell

Top Answer
User Avatar
Wiki User
Answered 2010-08-05 21:40:17

Attach flex hose from pool skimmer outlet to pump inlet.

Attach second hose from pump outlet to filter inlet

Attach third hose from filter outlet to pool return

001
๐Ÿ™๐Ÿฟ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

What is better a Sand filter system or a saltwater filter system for above ground pools?

Is a sand filter system or a saltwater filter system for above ground pools?


How do you replace the sand in my pool filter?

Go to your pool shop and they will be able to supply you wit a Venturi pump these hook onto your garden hose and can suck the sand out of the sand filter.


What is a normal operating pressure for a jacuzzi sand filter for an above ground pool?

What is a normal operating pressure for a jacuzzi sand filter for an above ground pool?"


How do you clean the sand in a sand filter?

By backwashing. Slowly reverse the flow of water to wash the particles off the sand. The particles will then be suspending in the water above the sand filter, and the water will need to be siphoned out the top of the filter so that the particles do not go back through the sand filter.


Some sand in bottom of your pump from vacuuming pool above ground is this normal?

If you are getting sand coming into the pool and have a sand filter you may have to replace worn laterals in the sand filter.


How much sand is needed for above ground filter for 27 ft round pool?

That all depends on the size of the filter. It should say how many pounds of sand you need on the side of your sand filter.



How do you change the sand in an above ground swimming pool pump?

Swimming pool pumps do not use sand. You may have sand in your filter. The sand has to by removed by hand after taking th etop of the filter off.


How do you clean sand in sand pool filter?

If the filter is not running properly after back wash (still dirty) you may need to replace sand it is very easy but can hard on your back. The basics of changing filter sand are remove valve from top of filter, disconnect any hoses or pipes on filter, lay filter on its side and roll around to loosen up the sand, reach in and remove sand with your hand be careful not to damage the fingers in the filter they are expensive and can be very difficult to replace. After all the sand is out hose out filter and refill with new filter sand hook all hoses and pipes back up and you are done. Good Luck


Where do you get sand?

You can get swimming pool filter sand or a number of other filter media that can be used instead of sand from most pool shops. You can also get sand from under above ground pools from a builders supply or nursery.



Pictures of how to connect a filter to an above ground pool using skimmer?

Attempting to obtain step by step diagrams connecting an above ground pool to a sand filter.



What is the proper psi for a sand filter pool pump?

Backwash the filter when the pressure increases 10 psi above the pressure when it was clean


Why is Sand getting into pool from filter?

If you have a sand filter your laterals are worn these are the spokes at the bottom of the sand filter that allow water through but not sand.


How do you clean sand and replace sand on jucuzzi filter?

how do you clean jacuzzi sand filter, and replace sand



Why wont your sand filter filter your pool?

If the sand in it has been there too long it may require replacement. Or the sand filter is not set to recirculate and not to filter.


Difference between slow sand filter and rapid sand filter?

distinguish between slow and rapid sand filter



What has gone wrong if there is Sand in filter?

Nothing if its a sand filter However if sand is coming into the pool from the filter then you may have to replace one ore more laterals in the sand filter as they have worn and are letting sand through to the pool,


How do you check a sand filter for enough sand after the pool is filled with water and filter is attached?

Usually the top of the sand filter is above the water level of the pool, so all you have to do is unscrew the top and look in. However if the filter is below the pools water level you will have to cut of the water coming from and to the pool before you do. who added the sand? If you did - did you follow the manufacturer's instructions as to how much and what type of sand to use? Instructions tell you - - SPECIFICALLY - - how many pounds of # 20 silica sand to use.


What amount of sand is used in a sand filter?

It depends on how large the filter is.


How do you set up a sand filter?

Do you mean how do you install a sand filter?.


Your above ground sand filter is running at too high psi what do you do?

Try backwashing if that doesn't fix it check if it isn't time to change the sand.


Still have questions?

Trending Questions
Previously Viewed
Unanswered Questions