Chevy Silverado
Chevy S-10
Dodge Caravan

How do you install a 1992 Silverado fan belt?

646566

Top Answer
User Avatar
Wiki User
2015-07-15 21:11:35
2015-07-15 21:11:35

most chevys have a routing diagram located near the radiator somewhere toward the front of the engine compartment.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The Villager has an electric fan and does not use a "fan belt".

User Avatar

If it is a serpentine belt you replace the tensioner pulley

User Avatar

Put your new fan belt around the pulleys of your 1992 Chevy Blazer. Tighten the fan belt with the tensioner pulley.

User Avatar

Pull back the belt tensioner and slip the belt off. Reverse procedure to install.

User Avatar

how do you replace fan belt on 95 Chevy S-10 2.2 engine

User Avatar

drive belt for what on this vehicle? do u mean serpentine belt,or fan belt,or timing belt?

User Avatar

The clutch fan on a 2004 Chevy Silverado is removed by loosening the alternator bracket and pulling the drive belt. The fan's retaining bolts can then be removed and pulled from the engine.

User Avatar

you do not have a relay for a fan belt. just change them.

User Avatar

The serpentine belt has a tensioner that you nust pry up to remove the belt. There should be a schematic of the routing of the belt on the fan shroud. If not, draw one before removing it.

User Avatar

Loosen the component slide it towards the engine to lossen the belt, remove belt. Install in reverse. If the fan is your problem it is held on with 4 small bolts, remove them and the fan. P/S you should be able to work the belt around the fan blades without removing the fan. On_mitch

User Avatar

pull on your tensioner to remove pressure with a wrench remove belt and reverse

User Avatar

This is a trick question isn't it? My MH Barina (5 door) has an electronic radiator fan. That is, it is driven by an electric motor rather than a fan belt.

User Avatar

Loosen the tensioner pulley. Put the fan belt around the pulleys. Pry the tensioner pulley to the right until the belt is tight. Tighten the tensioner pulley nut.

User Avatar

look at the diagram that's on the fan shroud

User Avatar

Remove the fan belt, by loosening the tensioner pulley. Remove the fan clutch with the retaining bolts. Reverse the process to install the new fan clutch.

User Avatar

Check for a gas leak maybe on the belt and check the belt for alignment.

User Avatar

first u must loosen bolt on power steering belt tensioner till the belt will come off ,then loosen alternator bolts and push alternater till belt is loose enough,then take fan belt off ,install new fan belt,use crowbar on alternator to tighten fan belt,then put power steering belt back on and tighten tensioner till its at spec. then retighteh tensioner center bolt.

User Avatar

Drain the radiator. Remove the fan and fan shroud if needed. Remove the pump belt. Unbolt the pump and remove it. Install the new pump. Reinstall the belt, fan and fan shroud. Refill the system with new coolant.

User Avatar

The diagram should be on the fan shroud. If it isn't, draw one before you take it off. It also is in the owners manual. Otherwise go to a used car lot and find a car with a like engine and draw your own schematic,./To change the belt (and if you have the original type belt tensioner) you need a small oil filter wrench to loosen the belt tensioner to fit the new belt on. Good luck.

User Avatar

Drain the radiator. Remove the pump belt, fan, and fan shroud. Unbolt the pump then remove it. Bolt the new pump on, and install the fan an shroud. Put the belt on and refill the radiator with fresh coolant.

User Avatar

Hi their should be a diagrahm on or around the fan shroud

User Avatar

"Which fuse controls the fan for the ac on a 2006 Chevy silverado?"

User Avatar

There is no fan belt it is an electric fan. Are you referring to the serpentine belt?

User Avatar

There is no fan belt. The fan is electric.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.