answersLogoWhite

0


Best Answer
Copy

It takes a special gauge to install the crank sensor. It can be rented from some parts stores.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:29:38
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you install a crankshaft sensor on a 1993 Oldsmobile Cutlass Supreme?
Write your answer...
Submit

Related Questions

How do you install a heater core on a 1985 Oldsmobile Cutlass Supreme?

cutlass supremes are so baller


How do you install starter in 1993 cutlass supreme?

Stick the starter in the cutlass supreme.


How do you install a rear view mirror on a 1996 Oldsmobile Cutlass Supreme?

go to the parts store and get a rear view mirror mounting kit and follow the instructions to a T.


How do you Replace the belt tensioner on Cutlass supreme?

Begin by removing the serpentine belt from your Oldsmobile Cutlass. Remove the tensioner pulley retaining bolt. The retaining bolt will be in the center of the pulley. Reverse the process to install your new belt tensioner.


How do replace a power steering pump on an 1985 Oldsmobile Cutlass Supreme V8 5.0?

Remove the power steering hose. Remove the power steering belt. Remove the power steering pump retaining bolts. Reverse the process to install the new power steering pump on your 1985 Oldsmobile Cutlass.


How do you install a fuel pump in a 1998 Oldsmobile Cutlass?

Remove fuel tank for access


How do you change a blower motor on a 1995 cutlass supreme?

Remove the wiring harness from the back of your 1995 Oldsmobile Cutlass blower motor. Remove the blower motor retaining bolts. Remove the fan from the front of the blower motor. Reverse the process to install your new blower motor.


Can a chey 350 be mounted in an 86 cutlass supreme?


How do you change a oil pump in a 1972 Oldsmobile cutlass supreme?

Remove the oil pan, unbolt the pump, install the new pump,the pump drive is off the bottom of the distributor and must be aligned to go in properly.


Do you need to know what the torque would be to find out if the idler tension pulley has to be torqued when you install the serpentine belt on a 1995 Oldsmobile Cutlass Supreme?

there is not a specific torque for the idler pully. tighten it up with a ratchet and it will not loosen up


How do you install a fuel pump in 1993 Oldsmobile cutlass wagon?

Take the gas tank down as the pump is inside the gas tank.


How do you install brake pads on 1982 cutlass?

Replacing the brake pads on your 1982 Oldsmobile Cutlass is quite easy. Remove the brake pad Springs and caliper. The brake pads will come off. Reverse the process to install the new brake pads


Where can you get step-by-step instructions to install a gas tank in a 1987 Cutlass Supreme?

A Hanes or chilton manual


How do you install a new taillight assembly for a 1994 Oldsmobile Cutlass Supreme?

Seems silly.. take out the old one, and install the new one. Pull the carpet away from you in the trunk by your brake lights, and you'll see 3 screws with plastic wingbolt lookin things. Unscrew all of them, and you can pull the entire assembly out.


1993 Oldsmobile cutlass ciera fuel pump relay fuse keeps blowing?

sounds like pump is going, install new pump


Change oxygen sensor on 95 Oldsmobile cutlass ciera?

Remove the oxygen sensor vacuum to. Remove the oxygen sensor screws. Reverse the process to install the new oxygen sensor.


How do you replace a wiper motor for a 1999 Olds Cutlass?

Remove the wiper arm from your 1999 Oldsmobile Cutlass wiper motor. Remove the wiper motor wiring harness. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.


How do you install igniton cylinder Oldsmobile cutlass supreme?

remove steering wheel with a puller, remove turn signal switch, remove tilt steering spring by pushing down and turning slightly counter clockwise, this should give you access to the torx screw . remove this screw and slide ignition lock cylinder out


How do you install crankshaft position sensor 95 mercedez Benz c220?

How do you install crankshaft position sensor 95 BENZ C220?


How do you install a starter in an 86 Cutlass?

Its 2 9/16 bolts and 2 wires... Its 2 9/16 bolts and 2 wires... Its pretty easy if its a Supreme


How do you install a new starter in a 1994 Oldsmobile cutlass supreme?

Remove the negative (black) cable from the battery. dissconnect any power wires running to the starter. remove two bolts located on the starter. Have someone help so they can hold the starter while you loosen bolts. When putting starter back in reverse procedure.


How do you install a crankshaft sensor on scion?

log on then you have to go to file then it should say install crankshaft to scion user. Click it then follow the instructions given.


Install crankshaft position sensor on 2004 Maxima?

where is the crankshaft position sensor on a 2004 maxima


How do you remove alternator from 1989 Oldsmobile cutlass sierra?

IT is only about 3 bolts release tension losen bolts unplug wire follow step in reverse install new one (disconnect battery first


How do you install a CrankShaft Sensor in a 95 Buick Century?

Pull the front cover off of it, Behind the Crankshaft balancer, The sensor is there. a diagram of how to install a creckshaft sensor.