well i hope you have a rack but i know that you don't me nither ok first jack the car in the air about 3 feet support car with jack stands and use just the jack. using a pickel fork to pop out not remove the tie rod end trying not to rip the greese boot once out move out of your way be tieing up using whit ever you find or have handy.don't forget to remove the nut from the tierod end befor poping apart . next remove the nut and bolt from balljoint then with a pry bar lission in my thought anything can be used that is small like to fit between the a-arm to pulldown and out. at this time you will be able to move the strut,brake calibel,rotor.next take axel nut off 32-34mm socket tap end of cv shakt with nut still on end of shaft side a is out side b with small pry bar slide between cv and transmission case and swiftly pry back on cv have rag ready to shove in where cv came out . elliotts9 PS repeat all backwards to install cv shaft
how to install cv axle on a 2002 e32o meredes
#1 axle is the steer axle, #2 axle is the front drive axle, #3 axle is the rear drive axle.
Only if the rear axle is a drive axle.
Sounds like a broken axle shaft
Transfer power from the transmission to the drive axleTransfer power from the transmission to the drive axle
The exact same thing as the first drive axle.
I fought with my axle nut on 2004 suzuki Verona for hours, then finally checked and it called for 236 ft/lbs.
There is no differential. The transmission is both a transmission and front wheel drive trans axle. It is all in one.
what are the signs of a damaged front axle and is it dangerous to drive a car with a damaged axle.
a pusher axle is in front of the drive axles, a tag axle is behind them
You will need to remove the tire and wheel from your 1997 Suzuki. Remove the axle end. Remove the wheel bearing nut. Remove the wheel bearing and the wheel seal. Reverse the process to install the new wheel bearing.
I am trying to do this myself,any suggestions ========== Do not turn transmission! I myself, 8/29/09
Wheelbase on heavy 3 axle trucks is measured from the center of the steer axle (1st axle) to the trunnion, or the midpoint BETWEEN the 2 drive axles (axles 2 and 3), not to the center of the rear drive axle (axle 3). Axle to axle is only used on 2 axle trucks. Note: be careful using wheelbase to calculate bridge laws, which can use 1st axle to 3rd axle measurements in its calculation depending on the state/province.
2007 ford focus sedan , rear axle nut , at wheelbearing/ 235 nm --- 174ft/ lb
Speed sensors are located on the axle
See the Related Link below.
The 2001 Forrester front drive axle nut torque specification is 90 pounds. The front drive axle nut should be torqued in 45 pound intervals.
A 6x4 tractor has three axles (one steer axle and two drive axles). In normal operations, only one drive axle is engaged, but the second axle can be engaged as well using a differential lock. 6x2 tractors are more common in Europe, Asia, Northern Africa, etc. They will have a steer axle, and a single drive axle. They will also have an additional axle next to the drive axle, which cannot be engaged to drive the vehicle. Often, this will be a lifting 'tag' axle, which in Europe would usually have one tire on either side, while some of Schneider National's Freightliner Argosy tractors in the US and Canada have a lifting rear axle with two tires per side to allow the same weight rating as if it were a drive axle.
Rear wheel drive...connects the transmission to the rear end. Transfers power from the motor to the rear axle. Front wheel drive... connects the transmission to each front axle. Usually refered to as CV or drive axle. Same purpose. The drive shaft contains the rod that takes energy from the engine and transmits it to the drive wheels of a car.
A trans axle is a transmission and differential rolled into one in a front wheel drive vehicle. The trans axle delivers power from the engine to the drive wheels.
It's the oil/fluid that is in the rear drive axle (and front axle on 4x4).
It depends if it is a 4 wheel drive truck. A rear driveshaft is used to drive the rear axle. A front driveshaft is used to drive the front axle on a 4X4.
Loosen the 3 driveshaft bolts disconnect the rear brake cable, pull the axle nut, and then pull the axle shaft. the drive side should be removed carefully and the brake side hub both just release upon removal.
98 accord does not have a rear axle- just spindle/hub/bearing
Underneath Car near rear axle