how to change a belt on a 1993 gmc first get the proper belt .then you look at the pullies to make shure they are all good . now there is a pully dampener at the top .you got to lift or push it down to release the tention . now you can remove they belt .mack sure you put it back on they pullys the same way it came off they pullys .if in dought look at the front of your veihcal and there should be a sticker there an follow the sicker on they header panel for they routing
drive belt for what on this vehicle? do u mean serpentine belt,or fan belt,or timing belt?
The Villager has an electric fan and does not use a "fan belt".
Because it's broken...
Pull back the belt tensioner and slip the belt off. Reverse procedure to install.
how do you replace fan belt on 95 Chevy S-10 2.2 engine
Should just be 4 bolts holding it on
You have to take off the alternator to be able to reach the fan . After you should oiul the belt to slip on the fan very easy . Put the alternator back on and your ready to go .
The serpentine belt has a tensioner that you nust pry up to remove the belt. There should be a schematic of the routing of the belt on the fan shroud. If not, draw one before removing it.
Loosen the component slide it towards the engine to lossen the belt, remove belt. Install in reverse. If the fan is your problem it is held on with 4 small bolts, remove them and the fan. P/S you should be able to work the belt around the fan blades without removing the fan. On_mitch
-drain coolent -remove serpentine belt -remove clutch fan -remove rad hose going to water pump -unbolt and remove water pump
You can find a diagram of the fan belt positioning on a 1992 GMC 1500 Sierra V8 in a repair manual. Haynes is a popular repair manual and is available from most auto parts stores.
pull on your tensioner to remove pressure with a wrench remove belt and reverse
your fan belt may be connected to your alternator if so loosen alternator romove belt put new one on and pull alternator back until proper tension is aqquired tighten
Drain cooling system Remove 4? bolts that hold fan in place Loosen and remove fan and fan belt Remove Pulley Disconnect water hoses upper, lower and bypass unbolt water pump and remove Clean mounting surface completely Install new gasket and pump Reverse to install
Loosen the tensioner pulley. Put the fan belt around the pulleys. Pry the tensioner pulley to the right until the belt is tight. Tighten the tensioner pulley nut.
look at the diagram that's on the fan shroud
Remove the fan belt, by loosening the tensioner pulley. Remove the fan clutch with the retaining bolts. Reverse the process to install the new fan clutch.
first u must loosen bolt on power steering belt tensioner till the belt will come off ,then loosen alternator bolts and push alternater till belt is loose enough,then take fan belt off ,install new fan belt,use crowbar on alternator to tighten fan belt,then put power steering belt back on and tighten tensioner till its at spec. then retighteh tensioner center bolt.
Drain the radiator. Remove the fan and fan shroud if needed. Remove the pump belt. Unbolt the pump and remove it. Install the new pump. Reinstall the belt, fan and fan shroud. Refill the system with new coolant.
It is the first plug closest to the distributor or timing belt and camshaft cover.Plain and simple.And that is standing directly in the front of the vehicle looking just past the fan,alt belt and fan.
Drain the radiator. Remove the pump belt, fan, and fan shroud. Unbolt the pump then remove it. Bolt the new pump on, and install the fan an shroud. Put the belt on and refill the radiator with fresh coolant.
There is a spring loaded tensioner near the top of the belt. Insert a wrench (whatever fits the job) and pull/push against it. Remove the belt.
There is no fan belt it is an electric fan. Are you referring to the serpentine belt?
There is no fan belt. The fan is electric.