I have a 95 Corsica with the 3.1 V6. I do all my own work, and this is the one thing that I hate doing. The way that I have been told to do it is similar to how I must do it in our 97 LeSabre. The front engine mount must be undone. You have to support the motor from the bottom, or it you have an engine hoist you can use that from the top. And if you do I envie you. You can use a floor jack to do this, just be careful of the oil pan. Once the motor mount is off, jack the motor up slightly. This should allow you enough room to remove the belt, and place the new one on the pulleys. Make sure that it is how you want it before you lower the motor back into place and securely bolt the mount back into place (personal advise from the Buick). That should be it, its not too difficult, just a pain in the a** for a belt. Good luck.
96 corsicas have electric fans which means there is no fan belt
how do you replace fan belt on 95 Chevy S-10 2.2 engine
The 1994 Chevy Corsica fan relay switch is located beneath the passenger side dashboard. The fan relay switch should be labeled as such.
pull on your tensioner to remove pressure with a wrench remove belt and reverse
location of the fan relay switch on a 1989 Chevy Corsica
The Villager has an electric fan and does not use a "fan belt".
Remove the wiring harness from the back of your 1996 Chevy Corsica blower motor. Remove the blower motor retaining bolts. Remove the fan from the front of the blower motor. Reverse the process to install the new blower motor.
Put your new fan belt around the pulleys of your 1992 Chevy Blazer. Tighten the fan belt with the tensioner pulley.
a picture of how to assemble a fan belt fro 98 Chevy venture van
Water may leak through a fan box on a Chevy Corsica if the water pump has broken. Another cause may be that debris clogged one of the drain holes.
Drain the radiator. Remove the fan and fan shroud if needed. Remove the pump belt. Unbolt the pump and remove it. Install the new pump. Reinstall the belt, fan and fan shroud. Refill the system with new coolant.
If the coolant fan does not operate on a Chevy Corsica, it is likely that a fuse is out. There could also be a mechanical defect in the fan or wiring.
how to change the fan belt on a 1995 Chevy blazer vortec motor?
If it is a serpentine belt you replace the tensioner pulley
Pull back the belt tensioner and slip the belt off. Reverse procedure to install.
Observe how the belt runs around the pulleys then take a 1/2" ratchet and insert it into the belt tensioner( on top near shiny pulley) and pry back the tensioner. Simply remove old belt and install new one. You will be surprised how easy it is. I hope this helps you. Mark
2004 2.4 fan belt route
drive belt for what on this vehicle? do u mean serpentine belt,or fan belt,or timing belt?
The serpentine belt has a tensioner that you nust pry up to remove the belt. There should be a schematic of the routing of the belt on the fan shroud. If not, draw one before removing it.
V-belt driven, clockwise.
REMOVE THE SINGLE DRIVE BELT, THEN REMOVE THE 4 MOUNTING BOLTS BETWEEN THE FAN AND THE BELT PULLEY. THE FAN MIGHT NEED TO BE WIGGLED OFF
There should be a diagram under the hood, or radiator fan shroud, on my 91 awd its on my power steering canister underneath the windshield, just look at that and follow the instructions. hope this helps
Loosen the component slide it towards the engine to lossen the belt, remove belt. Install in reverse. If the fan is your problem it is held on with 4 small bolts, remove them and the fan. P/S you should be able to work the belt around the fan blades without removing the fan. On_mitch
Remove the wiring harness or the fan motor belt, depending on the year of your Chevy Cavalier. Remove the fan motor retaining bolts. The fan motor will come off.
follow the instructions on the fan shroud
FIRE WALL SIDE OF ENGINE, A LITTLE UNDER THE EGR VALVE. T HEMPLE