answersLogoWhite

0

  • Auto Parts and Repairs
  • Chevy Blazer
  • Chevy S-10
  • Chevy Blazer S-10

How do you install a new gas gauge in a 1985 S10 Blazer?

User Avatar

Wiki User

βˆ™ 2011-09-13 04:47:54

Best Answer
Copy

its actually very simple.i had to do the same thing about 2 or 3 days ago...there should be 5 to 7 factory screws, then after you remove that there should be a clear pane of plastic, there should be 4 screws on that, then after that a black cover should come right off, and your guages are exposed

2011-09-13 04:47:54
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Add your answer:

Earn +5 pts
Q: How do you install a new gas gauge in a 1985 S10 Blazer?
Write your answer...
Submit

Related Questions

What is the wheelbase for a 1985 S10 blazer?

what is the wheel base for 1985 s10 blazer


Are there any backseats in a 1985 S10 Blazer?

yes


Where is the electronic control module on a 1985 Chevrolet S10 Blazer 2.8 engine?

There is no ECM in the 1985 S10, it is carbourated.


How do you get the gas gauge to work on a 1985 Chevy S10 Blazer?

If the gas gauge is not reading there is possibly a short somewhere between the fuel tank and the gauge or the gauge itself is broken. I have found that in most cases the sending unit in the tank has failed.


What should the voltage gauge read on a S10 Blazer?

13.9 to 14.2 volts.


What voltage is the hot wire to the coil on a 1985 s10 blazer 2.8?

12 volt.


What is the part number for a 1985 S10 Blazer GMAC wiper turn signal cruise control lever?

The 1985 S10 Blazer GMAC Êoffers a delay wiper on the black cruise control lever. ÊThe part number is AM-64109149.


Where to hook up the wires for a tach on a 1985 Chevrolet s10 blazer?

You should hook up the wires for a tach on a 1985 Chevrolet s10 blazer to the negative side of the coil. You should be sure to identify the positive and negative sides of the coil.Ê


How much does a 1985 s10 blazer weight?

A 2wd w/ a 2.8 v6 weighs 3200lbs.


What does the indicator light on my 1985 s10 blazer mean?

We need to know which indicator light you speak of.


Will a transmission out of a 1995 s10 blazer fit a 2000 s10 blazer?

Yes


How do you take the drive shaft out of a 1985 S10 blazer?

out a s10 short bed truck putting back does the front have to have the bushing by the seal can you take it off


Will a motor from a 1990 s10 blazer fit in a 1995 s10 blazer?

Yes it will fit.


What is the curb weight of a 1985 Chevy S-10 blazer?

The 1985 Chevrolet S10 Blazer has a curb weight of 4,462 pounds. The standard fuel tank capacity for this vehicle is 24.83 gallons.


What is the timing degrees for a 91 s10 blazer 4.3 2wd?

on a 91 blazer s10 4wd


Where is fuse for power windows in Chevy s10 blazer?

We need to know what year that S10 Blazer is.


Will an alternator from a 2000 Chevy blazer fit a 2002 s10 blazer?

An alternator from a 2000 Chevy blazer will fit a 2002 S10 blazer with a little fabrication.


Is it possible to put fuel injection on a 1985 Chevy S10 blazer?

It already has throttle body fuel injection.


What size tire are on a 2001 Chevy s10 blazer?

235x70x15 this tire size on my 2001 s10 blazer


How do you replace dome light on s10 Chevy blazer?

how do you replace dome light in s10 chey blazer?


Does a s10 blazer and s10 truck rearend interchange?

YES


How do you change the spark plugs on a 1985 s10 blazer?

You can begin by removing the spark plug wires from your 1985 Chevrolet S 10 Blazer spark plugs. Use a 5/8 deep well socket to turn the spark plugs out. Turning the socket to the left will loosen the spark plugs. Reverse the process to install the new spark plugs.


How do you repair headlight wiring on a 1985 s10 blazer that dont work at all?

Have you checked that the headlight switch is working properly?


Does a 2004 Chevy Blazer have chip in the key?

No it does not if it is a s10 blazer


91 grill in a 87 s10 blazer?

This can be done, though some modifications may be needed. If you need to replace your core support (rad support) as well, order a core support for a 91 S10 blazer. This will help do away with the mounting issues. I did this to a 1985 S10 blazer and the grill fit fine with the factory core support, but not all of the mounting locations matched.