answersLogoWhite
Serpentine Belts
Pontiac Bonneville
Ford Excursion XLT

How do you install a serpentine belt on a 1997 Pontiac Bonneville?

141516

Top Answer
User Avatar
Wiki User
Answered 2007-09-02 02:19:49

You have to remove the bottom bolt and spacer for the motor mount. Easiest way is to take the right front tire off, remove the inner fender well access flap. The bolt has a nut on the out side that has to be removed. Then the stud that goes through the mount into the engine has to be removed. Slip the belt over the pulleys and reverse the procedure. Thirty minute job.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Your Answer

Related Questions


Yes, I need a diagram of the serpentine belt for a 1997 3.8 liter Bonneville SE without a turbo charger.


locate blend door actuator for 1997 pontiac bonneville se


there is no difference between the 2..to be sure when u go to the parts store have him check it out..


Begin by removing the wiring harness from the back of your 1997 Pontiac Bonneville headlight. Remove the headlight assembly retaining bolts. Reverse the process to install your new headlight.


Begin by training the water from your 1997 Pontiac Bonneville cooling system. Remove the heater core water supply hoses. Remove the heater core retaining bolts. Reverse the process to install the new heater core.


The rotor thickness for your 1997 Pontiac Bonneville is 0.75. When the rotor falls below this thickness a certified mechanic can no longer use the rotor.


You can remove your 1997 Pontiac Bonneville ignition switch by removing the retaining ring at the top of the ignition switch. The ignition switch will slide out.


A person can find a wiring diagram for a 1997 Pontiac Bonneville at most GM dealerships. The dealerships are happy to help customers with any requests.


The Autolite website lists a gap size of .060 the 1997 Pontiac Bonneville.


Google Pontiac boneville ac compressor bypass pulley. There are a few places that sell a replacement pulley that goes in the spot of the compressor that allows use of the original serpentine belt.



go to www.kellybluebook.com and it will tell you the value


The 1997 Pontiac Bonneville has a coolant capacity of 5.6 gallons. The manufacturer recommends that 50 percent of your coolant should be anti-freeze.


Remove serpentine belt. Remove pulley. Install new pulley. Install serpentine belt.


You will need to remove the front engine cover, on your 1997 Pontiac Bonneville, in order to change the supercharger belt. Loosen the tensioner pulley to remove the belt.


The fuel pump relay in a 1997 Pontiac Bonneville is found under the hood of the car in front of the wiper blades. To access the pump relay, there is a plastic cover with three tabs which must first be removed.


The fuel pump is located inside the fuel tank.


The power steering reservoir is underneath the alternator by the firewall.


its below the steering wheel towards the right, its a litle plug-in


There are a few posts as to the answer to this question. You need to remove the serpentine belt from the alternator, unplug the electrical connections from the back, remove the mounting bolts, and install the new alternator. Hope this heps.


i need a digram on how install a v belt on a 1997 e420 Mercedes


it is a 2001 Pontiac Montana that has broken three bealts so far I need to know what pully I will need to replace?


Call any local bone yard, and have them look it up in a trash book. (Hollander)


To answer this question, There are 2 wheel sizes one is 15 inches and the other is a 16 inch.


The blower motor on a 1997 Pontiac Bonneville is located next the evaporator core. It will be mounted behind the glovebox on the passenger side of the vehicle. Remove the glovebox, mounting hardware, and sensor clips. The blower motor will be able to be replaced.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.