Chevy Suburban
Chevy Blazer S-10
Ford Bronco
Spore

How do you install a starter on a 2000 S-10 Blazer?

272829

Top Answer
User Avatar
Wiki User
Answered
2011-01-16 08:14:45
2011-01-16 08:14:45

Place front of vehicle on elevated stands. slide under the engine towards the passenger side. just about where the front right tire is located you will see the starter it is held in place by two 14 or 15mm bolts. now be aware I changed a 91 starter and I wound up having to remove the bell housing that covered the flywheel gear. very difficult because I had to drop the front U joint to access all the bell housing bolts. then wound up having to repack the bearings in the ujoint.I hope in your case the engineer that designed the 91 had nothing to do with the 2000s design.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


An alternator from a 2000 Chevy blazer will fit a 2002 S10 blazer with a little fabrication.

The starter solenoid is attached to the starter.

Will a 2000 blazer transmission fit a 1998 s 10 chevy 4x4 truck

It would bolt in but you would have fuel injection problems.

how to remove the starter from a 92 s-10 4x2 with a 2.8 engine

Should be on top of the starter - follow the + battery cable

The 1995 Chevrolet S 10 Blazer starter relay switch simply plugs in and out. You can find the starter relay switch in the fuse box.

Yes, a 2000 GMC Jimmy hood is compatible to a 2000 Chevy Blazer. This is only on the S10 Blazer though.

Is the S10 a 4x4?If not, measure everything and if it is correct Go for it

It is attached to the starter, just follow the positive battery cable from the battery, it will lead you to the starter solenoid.

the 1996 and 1997 are the same and would not work in your 2000 straight from GM

There are several reasons why a 1999 Blazer S10 may not turn over. Some reasons could be bad spark plugs, dead battery, or even a bad starter. A mechanic will be able to determine the cause.

Probably the fuel pump is bad.

what is the wiring diagram for the o2 sensor on 2000 s10 blazer. it has 4 wires. what what do they all do /

remove passenger front tire then fold back the water guard then you will access to the starter

what is the wheel base for 1985 s10 blazer

Follow the positive battery cable from the battery down, the other end will be attached to the starter.

first you take it in then pay them to do them for you!!!!!!!!!!

Inadequate fuel pressure. If that 2000 S10 Blazer has a 4.3 engine, it needs 61 to 66 psi (engine off with fuel pump running) to run properly.

Starter solenoid switch is stuck closed.

you have to remove the starter to replace the relay and the relay cost almost as much as the whole starter so you are better off just replacing the whole starter.

It is mounted on the starter motor itself. When you get another starter, it will have the solenoid mounted on it already. If it is bad, just replace the starter, I would not change just the solenoid.

Disconnect the battery cable. Remove the bolts that hold the starter in place. Disconnect the wires. Instahlation is in reverse.

The starter motor/solenoid on a 2000 Chevy S10 Blazer is on the lower passenger side of the engine block. If your trying to replace it, first, disconnect the negative battery terminal. Remove the differential carrier shield. Disconnect the bolted solenoid cables. Remove 2 vertical bolts securing the starter motor to the engine block. When reinstalling starter, tighten mounting bolts to 50 Nm/37 lb. ft.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.