answersLogoWhite

0


Best Answer

First , if your talking about the electrical switch (most likely mounted on the column under the dash) you just need to remove the two small screws holding it down and lift it up to remove. If however you are talking about the lock tumbler mounted in the column that you insert the key into, take it to a shop. It requres a special compression tool needed to compress the lock ring for removal underneath the steering wheel as well as a steering wheel puller to remove the steering wheel. You cannot remove the lock ring without damaging something if you are not experienced in this procedure without the tool. Suggest take it to a shop or locksmith as damage could get reall expensive as well as rendering your vehicle undriveable. Sorry

User Avatar

Rollin Wiegand

Lvl 10
1y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you install an ignition switch lock and key on a 1994 Chevy truck with tilt steering wheel picturs I can print?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you install ignition switch 1988 gmc truck?

You need to remove the steering wheel first with a puller. There is a latch you can trip with a small screwdriver that will let the ignition switch slide out. Simply replace the switch and put the steering wheel back on.


How do you replace the ignition of a 1992 Lincoln Town Car?

To replace Ignition Switch, first you have to remove the old one. To do this you disconnect battery ground cable. Remove the upper steering column shroud by removing the five self-tapping screws. Remove tilt steering column lock lever, Remove lower steering column shroud, disconnect the ignition switch electrical connector, turn ignition switch lock cylinder to the "run" position, remove the two screws retaining ignition switch, and finally unhook the ignition switch from the actuator. Now to install the new one.Make sure that the ignition switch lock cylinder is in the "run" position. You can test for the "run" position by rotating the ignition switch lock cylinder approximately 90 degrees from the "lock" position. Hook up the ignition switch into the actuator. You might have to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes. Install retaining screws. Connect electrical connector to ignition switch. Connect battery ground cable. Check ignition switch for proper operation, including start and accessory positions. Also, make certain that the column is in the "locked" position. Then Install upper steering column shroud. Install the lower steering column shroud and tilt steering column lock lever.


How to change the ignition switch?

Lower the steering colunm. the ignition switch is located on the top of the steering column about 6 inches from the firewall.


Where is the ignition switch in a ford expedition xlt v8?

The ignition switch is located on the steering column right side, just below the steering wheel.


How do you replace an ignition switch for a 2000 blazer?

You will need to remove the retaining ring at the top of your 1978 Chevrolet Blazer ignition switch. Slide the ignition barrel out and remove the wiring harness. Reverse the process to install the new ignition switch.


How do you install ignition switch on 1989 Chevy G 10 van?

how do you install new ignition switch on 1989 chevy G10 van?


How do you replace ignition switch on a 2000 silverado?

Remove the ignition switch retaining ring. Pull the ignition switch out. Remove the wiring harness from the back of the ignition switch. Reverse the process to install the new ignition switch.


Where is the ignition switch on a Mazda pickup?

by the steering wheel


How do you change ignition switch on 1998 Buick century Do you have to remove the steering wheel?

do I remove steering wheel to change out ignition


How do you install an ignition switch on a 1986 Chevrolet caprice?

Attach the wiring harness to the and of your 1986 Chevrolet Caprice ignition switch. Slide the ignition switch into the ignition slot. Tighten the ignition switch with the retaining ring.


How do you install ignition switch on 1991 Mazda Navajo?

How to remove ignition switch on a 91 Mazda Navajo


How do you change ignition switch in 1995 Chevrolet Silverado?

Really easy. Ignition switch is mounted on top of the steering colum under the dash, 2 small bolts hold it to steering colum, wiring harness plug, and operating rod. Remove wiring harness, two bolts and operating rod, then in reverse order install new switch.