answersLogoWhite

0

  • Dodge Ram
  • Jeep Grand Cherokee Laredo
  • Jeep Grand Cherokee Limited
  • US Governors

How do you install governor pressure sensor for a 1997 gand Cherokee 8-cylinder 5.2L?

User Avatar

Wiki User

βˆ™ 2008-04-13 18:05:44

Best Answer
Copy

remove tranny pan, get ready to take a fluid shower, remove de ptc, and the Pcm on the trv, and get laid, cheers

2008-04-13 18:05:44
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

How do you install governor pressure sensor 1997 Town and Country van?

A 1997 Chrysler Town and Country does not have a governor pressure sensor.


How do you install governor pressure sensor for a 4.0L 2001 grand ckerokee?

Here's a link that will help. http://www.automotiveforums.com/vbulletin/showthread.php?t=350038&highlight=governor+pressure+transducer


How do you install a fuel pump in a 1993 Jeep Cherokee Sport?

Release the fuel pressure . Remove the gas tank . On the top there is a lock ring, loosen it and install the new module assembly.


How do you install a fuel pump on a 2000 Jeep Cherokee?

how to install a fuel pump on a 2000 jeep Cherokee 6 cylc


How do you install a soft top on a Jeep Cherokee?

Cherokee is a hard top only vehicle.


How do you install passenger tail light kit for a 2004 Grand Cherokee Laredo?

How do you install passenger tail light kit for a 2004 grand cherokee?


How do you tell if the problem is oil pump or oil pump sensor on a 96 Grand Cherokee limited?

Remove oil pressure sensor and install a manual gauge


How do you install a thermostat on a 1997 Jeep Cherokee?

how doyou install a thermostat in a 1994 jeep


How do you change governor pressure sensor and solenoid for 2004 jeep Cherokee Laredo?

I am going to give you the information for a 4.0L, if you have the 4.7L V8 let me know and I will send that informationThis is a fairly easy repair, when I do this I replace the governor pressure sensor and the transducer, that way you wont have to go back in if the other fails, you should also replace the filter while the pan is offHoist and support vehicle on safety stands.Place a large diameter shallow drain pan beneath the transmission pan.Remove bolts holding front and sides of pan to transmissionLoosen bolts holding rear of pan to transmission.Slowly separate front of pan and gasket away from transmission allowing the fluid to drain into drain pan.Hold up pan and remove remaining bolt holding pan to transmission.While holding pan level, lower pan and gasket away from transmission.Pour remaining fluid in pan into drain pan.Remove screws holding filter to valve bodySeparate filter from valve body and pour fluid in filter into drain pan.Dispose of used trans fluid and filter properly.Disengage wire connectors from pressure sensor and solenoidRemove screws holding pressure solenoid retainer to governor body.Separate solenoid retainer from governorPull solenoid from governor bodyPull pressure sensor from governor body.Remove bolts holding governor body to valve body.Separate governor body from valve bodyRemove governor body gasket.Before installing the pressure sensor and solenoid in the governor body, replace o-ring seals, clean the gasket surfaces and replace gasket.Place gasket in position on back of governor bodyPlace governor body in position on valve body.Install bolts to hold governor body to valve body.Lubricate o-ring on pressure sensor with transmission fluid.Align pressure sensor to bore in governor body.Push pressure sensor into governor body.Lubricate o-ring, on pressure solenoid, with transmission fluid.Align pressure solenoid to bore in governor bodyPush solenoid into governor body.Place solenoid retainer in position on governorInstall screws to hold pressure solenoid retainer to governor body.Engage wire connectors into pressure sensor and solenoidInstall transmission fluid pan and (new) filter.Lower vehicle and road test to verify repair.Parts should run right around $260.00 plus 2.0 hours labor


How do you install governor pressure sensor for a 5.2 L Dodge ram 1500?

The governor pressure sensor is in the trans.,so it means removing the pan .It may also mean removing the valve-body depending on if it is above or below the valve-body.I suggest that you search on line for more specific instructions .


How do you install a body lift on a Jeep Cherokee?

Jeep Cherokee's are unibody. You cannot install a body lift.


How do you install Daytime Running Lights on a 2006 Jeep Grand Cherokee?

no


How do you install a front bumper on a 2006 Jeep Grand Cherokee?

carefully


How do you install a trailer wiring harness on a 2000 Cherokee Classic Jeep?

from download.com


How do you spell Mary in Cherokee language?

Mary would be spelled ᎹᎵ (pronounced Mali). (If you can't see the Cherokee letters, it means you need to install a cherokee font on your computer. Just search for a free cherokee font and download it.)


How do you spell sheila in the Cherokee language?

Sheila is spelled ᏏᎳ (pronounced see-lah) (If you can't see the Cherokee letters, it means you need to install a cherokee font on your computer. Just search for a free cherokee font and download it.)


How do you install a fuel filter in a Jeep Cherokee?

Most all Cherokee fuel filters are in front of the fuel tank on the drivers side under the vehicle.


Can you install a 1996 Jeep Cherokee 2 wheel drive auto transmission in a 1996 Jeep Grand Cherokee 2 wheel drive?

Yes


How do you install a pressure transmitter?

If we have mechenical clairience as pur hookup we can install the p-t.


Can you install a 1996 4.0 in a 1990 Cherokee?

I put a 99 head and block in an 89.


Will a 1996 window regulator for a Jeep Cherokee sport fit a 1998 Jeep Cherokee Sport?

yeah it will just make sure u install it right


How do you check oil pressure on 2003 HD XL1200C?

install an oil pressure gauge


Where do you install the oil pressure gauge on a Chevy 350 small block?

how to install the oil pressure gauge on a Chevy 350 small block


How do you install a governor on a 5hp Briggs and stratton engine?

You loosen the nut own the governor arm turn the arm clockwise and then turn the governor shaft clock wise. Tighten nut That should do it.


Can you install pressure regulating valve upside down?

no