This is a FUN one! Get ready for cut up hands and a question to yourself of why you didn't pay someone to do this. Anyway, here we go... Remove the fascia that has the lock & window controls on the doorpanel. (screw & lock/window fascia snaps). Unclip window & lock switches, push out towards the front. Be careful not to break these. Remove screw for armrest, pull doorpanel off from the bottom to the top. Lift panel 'up' off of top. In the doorjamb, on the door, remove the small bolt that goes to the back of the handle (10mm). Now, there's 2 ways to go from here. One way is easier to maneuver, but involves disassembling the inner steel panel (lots of time & patience). The other way is harder, and involves snaking your arm throughout the sharp small crevaces, as well as blindly (may take as much time if you have large arms/hands). Since this may be your first time, neither way would be easy... So I'll describe the 'easier' way. Remove the clear plastic on the door, remove the screws around the inner steel panel (9/32). Remove the bolt at the bottom front of the steel panel (10mm). Carefully lift up on the steel panel, use your knee to prop it upwards. Now gently pull the steel panle back, and unsnap the 2 linkage rods from the steel panel. Use a small flat screwdriver and unclip the retaining clips at the end of each linkage. Remove linkage from power lock motor (pulls downward & slips out). Disconnect power window motor. Here's more fun.. It's better to have 3 hands for this part.... Lift off steel inner panel and turn ut to release the window regulator from the backside of the steel panel. Now, turn it some more to release the 2 rollers that goes to the bottom of the window, the window will drop. Pull out the inner steel panel Look at the backside of the door handle, and remove the 2 clips & linkages that attach to it. Remove doorhandle. Again, you will need tons of patience with this task.
you never gave me the answer.....
Inside handle, outside handle, sliding door handle?
Remove the inside door panel of your 1994 Chevy Lumina. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install the new door handle.
you have to remove the interor door panel then take and pull up on the outside handel you will see a rod on the end of ti there is a plastic peace gently un clip the plastic peace by turning it. now there should be 2 nuts on the back of the handle remove them. and if your sierra has the option on it there will be a lock cylinder that is held on by a c clip remove that and you should be able to remove the whole handle
Need to know if it is an inside or outside door handle.
You will need to remove the inside door panel of your Mustang. Remove the linkage from the outside door handle. Remove the outside door handle retaining bolts. Reverse the process to install the new outside door handle.
See this document: http://www.jpcustoms.com/store/documents/signalmirrors.pdf This is actually a procedure to install some mirrors, but the process of removing the panel is shown. Jack
with a screwdriver
Assuming you are referring to the outer door handle, remove the inner door panel and look at the back of the handle. You will see a couple of steel rods attached to the handle, remove these(they just unclip)and move them out of your way. You should be able to see a couple of small nuts holding the handle to the door. Remove these and the handle can be pulled out of the door from the outside.
You can replace the inside drivers door handle by removing the door panel. With the door panel removed the door handle mechanism will be visible. Remove the linkage from the door handle. Remove the door handle retaining bolts. Reverse the process to install the new door handle.
its the keyless entry
Remove inner door panel for access
You need to remove the Door Panel and you can reach the attaching nuts from there.
Remove the inside door panel from your 1996 Dodge Avenger. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install your new door handle.
Remove inner door panel for access
take the inside door panel off and you will see the bolts that hold the handle on, take the bolts out and unhook any linkage to the handle and pull the handle off from the outside of the door, just reverse directions to install the new handle.
go to autozone,buy a handle remover/install tool.very simple and direct.
pull inside door panels off and unbolt the handle from the door from the inside, install new gasket and rebolt handle.
hi i have a 2001 tacoma and the 2 exterior door handles are broken what tools do i need ??
I have a 1996 Chevy extended cab cheyenne pickup. i need to know how to install a door handle on the passenger side.
The spare tire lowering handle is probably located under the rear seat on the 1999 GMC Sierra, if the vehicle is an extended cab. If it is not the extended cab, look behind the driver's seat for the handle.
No, there is not a diagram to take apart the outside of a door handle. However, there is a diagram that shows how a door is held together, and from there a person can take apart the outside door handle.
How do you replace the outside door handle on a 1996 Chevy Tahoe?
Door handle to what?
What I did for my Yukon was to take the old handle off, by popping it out of its holes and then popping the new on into the holes, because it was riveted into the door, and didnt want to take them out, I did buy the whole handle though, just took the small handle part you hold on to off the new one, and popped it into the old one without taking anything extra off.