No. which manifold gasket are you wanting to replace? Intake or exhaust?
unbolt the head pipe then the manifold.
Where is the leak coming from. Most likely you will need to replace the exhaust manifold gasket which will require removing the exhaust manifold.
If the exhaust manifold gasket is leaking the only fix is to replace it with a new one.
The exhaust manifold needs to have a gasket in place to help seal the juncture between the manifold and the engine. After the gasket and gasket sealer are in place, tighten the bolts for the exhaust manifold. The exhaust pipe can then be replaced on the new exhaust manifold.
if it is just a blown exhaust manifold gasket it can ruin your valves, so replace it correctly and make sure everything is clean before putting on the new gasket
In most cases a new gasket is required, but no sealant.
You will need to remove the exhaust manifold retaining bolts in your 1993 Chevy Astro. Remove the exhaust manifold. Remove the exhaust manifold gasket and clean the surface. Reverse the process to install the new exhaust manifold gasket.
sell your van the studs for the maniflold are going to break and you most likely will have to replace head Between the exhaust manifold and the head is the manifold gasket. Where the exhaust pipe connects to the exhaust manifold is a manifold doughnut gasket.
You have to replace the gasket because when you take the manifold off it brakes the seel and air will be sucked into the manifold and your vehicle will hardly run, and you wont be able to drive it You have to replace the gasket because when you take the manifold off it brakes the seel and air will be sucked into the manifold and your vehicle will hardly run, and you wont be able to drive it
get a chilton repair manual and it will tell you how.
Remove the exhaust pipe from the exhaust manifold. Remove the manifold bolts. Remove the manifold. Remove the manifold gasket and clean the surface. Reverse the process to install the new manifold gasket.
an exhaust flange gasket, is the gasket,commonly called a donut that is used to seal where the exhaust pipe is bolted to the exhaust manifold
You have to remove the exhaust pipe from exhaust manifold on starter side. Now you have access. Get exhaust pipe to exhaust manifold gasket first, you will probably need to replace it after taking them apart.
that can be any number of things. 1 check or replace the distributor. 2 check your head gasket. 3 if its back firing it doesnt always mean u jumped timing, your exhaust manifold gasket could be bad and you might be getting exhaust fumes in your intake manifold. note- intake manifold and exhaust manifold share 1 gasket
Remove the intake and exhaust manifold, then remove the head.
remove the intake and exhaust manifolds. there are bolts that attach them onto the head and there are bolts near the carburetor that attach the intake manifold to the exhaust manifold.
An exhaust leak is usually the result of a bad gasket or a cracked manifold. For a proper fix, either the gasket or both the manifold and the gasket must be replaced.
there is no gasket on the exhaust manifold. i have a 93 escort lx wagon and i have a leak somewhere and i looked at the exhaust diagram at my local napa and it doesnt show a gasket. * Not sure which diagram you were looking at but there is DEFINITELY a gasket... Look up exhaust manifold on any popular car site and you will clearly see one.
You must remove the exhaust manifold, intake manifold, and then remove the head. This is a major repair that should only be attempted by a pro.
You do not repair a head gasket you just replace it. Major repair involving removing the intake & exhaust manifold, and the heads.
Exhaust leak at Exhaust manifold to head gasket or oring at exhaust manifold pipe.
A blown manifold exhaust gasket, is simple to explain. The Exhaust manifold ,are bolted to your heads. Which the exhaust pipes are connected to. There is a gasket that goes between the Header and head. What you have is that the gasket is leaking. To fix the problem you have to unbolt the manifold from the head and replace all the gaskets. Dependeing on make and model, you may have a one peice gasket or if you have individual gaskets. all you do is loosen the Mainifold and slip out the old ones and slip in the new ones. Depending on how old and rusty your Mainfold is , you might have to unbolt the Mainifold all the way off. and/of take of the exhaust pipe. But it should be simple. Hope that helps out some.
A bad exhaust manifold gasket could do that.
Remove intake and exhaust manifold. Remove head and replace the gasket. This is a major repair best left to a professional.