iT IS SIMPLE, fIND THE BELT TENTIONER, IT IS A SPRING LOADED ARM WITH A 3/8" square hole in it near the idler pully, use a 3/8" rachet or braker bar to move it up, this will release the tension on the belt, be sure to rout the new belt properly! clay
You have to loosen the tension on the belt by loosen the nut normally found on the pulley located by the motorblock, manifold or even by the alternator pulley it's self.
yes, most of the panels can be used from one to the other
The difference between a sedan and a sport coupe.
what is the ratio of gears in a 1986 cutlass
Can you use the alternator from an EA ford falcon sedan 89 model to put in a EB ford falcon sedan 91 model?
The diagram to the alternator of a 1988 Sedan Deville can be found in the cars repair manual. It can be bought at an auto part store.
The shift knob should turn and loosen to the left. By turning this to the left it will loosen and come off, then put the new on and turning to the right until it's firm.
Sometimes the Cutlass sedan and the Delta 88 would share the same wheel design.
well first disconnect the battery, then remove the belt by using a pull bar at the pulley to release the tension of the belt to take off the belt, then unplug the wire harness that's plugged into the alternator then remove the 3 bolts from the alternator.
It is built into the alternator.
How to remove and replace a steering column on a 95 Cadillac Sedan Deville?
base sedan 3.1 v6 is 155 hp sl sedan 3.1 v6 is 160 hp sl coupe 3.1 v6 is 160 hp gls sedan 3.1 v6 is 155 hp
I did a alternator replacement on my 96' Lumina Sedan 3.1. In the engine compt. there's a diagram showing the serpentine belt flow and belt tensioner location. 1. Remove the belt after releasing the tension. 2. remove the bolts from the alternator & wire plug connecion. 3. Replace & reverse order. Pretty straight forward.
if you are looking under the hood it is just to the right of the motor. it has a fan belt atttached to the right side of the alternator.
Is this a sedan or coupe/convertible? The sedans had the common setup and the coupe/convertibles had the mini-quads.
No. Everything about the two cars is completely different.
it has a self tensioner pulley No adjustment required
a 1970 to 1980s Internally regulated alternator, a knowledge of how to change the wiring and an ability to build the brackets.
Remove rear wheels Loosen brake lines - but do not toally remove Loosen and remove 2 caliper mounting bolts remove brake line
tag on alternator, but probably 35 amps >>CORRECTION>> adding "alternator" to the question is correct, however the amperage rating for an alternator in a 94 Accord DX is 80 amps. Unless of course this DX model has a VTEC engine (very unlikely) then it will have a 90 amp alternator installed.
The 2 door coupe had a 112" wheelbase. The 4 door sedan had a 116"wheelbase. The Vista Cruiser had a 121" wheelbase.
how do I replace the AC expansion valve on a Mercedes C280 sedan. location and procedure
How To Replace Alternator on 98 to 02 Honda Accord V6 Coupe or Sedan One of the common symptoms for bad alternator is that all your dash lights will turn on while you are driving. = Removal: = * Ensure you have the anti-theft code for the radio. * Disconnect the battery negative cable first and then disconnect the battery positive cable. * Move the auto-tensioner "A" to relieve tension from the alternator belt "B" and remove the alternator belt.* Disconnect the condenser fan motor connector "A" from the condenser fan shroud.* Remove the condenser fan/shroud assembly "B". * Disconnect the 4-pin connector "A" and black wire "B" from the alternator.* Remove the mount bolt "A" and alternator bracket mounting bolt "B". Remove the harness clamp "C" from the alternator bracket.* Now you can remove the alternator. Depending upon the clearance you have, it might take a few tries before the alternator comes out of the car. = Installation: = * Follow the removal steps in reverse order to install the the alternator. * Adjust the alternator belt tension or the alternator AC belt tension. * Enter the anti-theft code for the radio.
how to replace front shock absorber on Mitsubishi 1997 TE Sedan
Assuming you're referring to the 4-door sedan model, the rear windows were fixed in place on that bodystyle (1978-87) - hence their being no crank to wind them down.