Auto Parts and Repairs
Brakes and Tires
Brake Pads and Rotors
Ford Ranger

How do you measure the rear brake drums in a 1992 Ford Ranger?

383940

Top Answer
User Avatar
Wiki User
2015-07-15 19:39:15
2015-07-15 19:39:15

Take them off and measure the machined surface for width and the diameter.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Yes, there is a cable that runs to the rear wheel brake drums.

User Avatar

It depends on what you are trying to determine. If you only want to know what size drums are on the vehicle, you should be able to determine that by measuring the drum diameter roughly from outside, across the center, or widest point. I believe, but don't remember for sure, that these vehicles came with either/or 9 or 10 inch drums on them, depending on the brake system installed. However, if you're trying to find out if they are still usuable, i.e. you hear grinding, or think you have damage, you must remove them, then measure the inside diameter with a brake drum micrometer, or any large inside diameter micrometer. The discard, or max diameter spec is stamped on the drum.

User Avatar

Hydraulic , front disc , rear drum , with rear ABS

User Avatar

Dance to the Drums Again was created in 1992.

User Avatar

where is fuel filter located on a 1992 ford ranger

User Avatar

just like any other car, make sure that the e brake is off then grab a hammer and hit (hard) it a few times it should loosen up.

User Avatar

Where is the oil pressure sending unit on 1992 ford ranger

User Avatar

on my 91 when i put new shoes on i adjusted the shoes out with adjuster until shoes touched drums and that also took care of my parking brake problem --- you may need rear brakes ???

User Avatar

What is a a/cl dv on a 1992 ford ranger xlt vacuum line

User Avatar

how to change a tie rod on a 1992 ford ranger xlt

User Avatar

Brake fluid location in 1992 Mazda mpv

User Avatar

The 1992 Ford Ranger did not come equipped with daytime running lights.

User Avatar

doors from 1986 to 1992 are the same for ranger bronco. yes will fit

User Avatar

The 1992 Ford Ranger ICM is located on the firewall in the engine compartment. The ICM will be on the drivers side of the firewall.

User Avatar

The 1992 Ford Ranger 4.0 liter had a 197 * Fahrenheit thermostat from the factory

User Avatar

A 1992 Ford Ranger is fuel injected so it would have an ELECTRIC fuel pump

User Avatar

The brake fluid in a 1992 Ford Escort gets put in the brake fluid reservoir. This is normally located on the master cylinder.

User Avatar

how do i change a lower ball joint on a 1992 ranger 2wd

User Avatar

It is quite easy to install the 1992 Chevy Lumina brake light switch. The brake light switch simply plugs in and out.

User Avatar

there are 2 rectangle pins that need to be pushed out with a punch/ screwdriver/ small pry bar

User Avatar

I own a 1992 ford ranger, 300c.i. v-6 and it is fuel injected.

User Avatar

I have a 1992 Chevrolet lumina and I had the same problem. what that means is your brake fluid is at a low level so check that.

User Avatar

You will need to remove the tire and wheel from your 1992 Nissan Stanza. Remove the brake pad spring and caliper. The brake assembly will come off. Reverse the process to install the new brake pads.

User Avatar

You can get a diagram for a 1992 Ford Ranger 3.0 engine from your local auto parts store. Repair books, such as Haynes, offer diagrams.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.