Subaru Outback
Ford F-350
Grand Am GT
Late Model 1979-New Ford Mustangs

How do you program a 1999 Subaru Outback key-less entry system?

515253

Top Answer
User Avatar
Wiki User
2006-01-02 19:49:07
2006-01-02 19:49:07

http://www.cars101.com/subaru/keyless.html#code%20alarm Should do it for ya...

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

See "Keyless Entry System" on page 10 of chapter 1 "Doors and Locks" in your "OWNER'S MANUAL".....

User Avatar

The keyless module is under the dash on the driver side. Do a search for Subaru Keyless Entry System H7110FS300

User Avatar

It has something to do with the immobilizer & keyless entry system programming. Take your car to the dealer. He will have to use a special scanner and laptop PC to program.

User Avatar

It's the theft part of the keyless entry system...reprogram your keyless entry and it stops... It's your cars keyless entry system that is the source of the problem. If the battery has been disconnected, it will cause this to happen. You have to find the keyless entry system reset button on my 1997 subaru it is under the dash on left side it is a black button hold the button in and at the same time turn the key to the on position (Do not start the car just turn to the on position) for about 20 seconds and it will reset

User Avatar

Not necessarily. I took a look at a supplier and if you have the same engine, the front pipe is the same number. It is very likely that since the car bodies of these two are from the same series first generation Outback, and they have the same engine, the exhaust will interchange.

User Avatar

You need to burp the radiator and cooling system.

User Avatar

The Emergency Killswitch in the Subaru Outback is located underneath the drivers-side steering panel. It is to the left of the steering column and looks like an inconspicuous button. Just press that with the keys in the ignition and with the electricity on.

User Avatar

Cooling system thermostat is at the bottom of the engine. Look for the lower radiator hose and trace it back to where it attaches to the engine block. Bingo!

User Avatar

The system requires between 1.3 & 1.5 lb of HFC-134a refrigerant...

User Avatar

Most likely a problem in the emission control system Have vehicle scanned to determine the problem

User Avatar

It is the tire pressure monitoring system.... it's means check your air pressure in your tires!!

User Avatar

Fuses for each year of Outback are different. Some years have the fuse arrangement in the owner's manual. Otherwise, each fuse position is marked with its function. A flashlight helps.

User Avatar

Oxygen sensors on all cars built in the last 20 years or so are located in the exhaust system. Subaru has them before and after the front catalytic converter.

User Avatar

It may be the heat shields on the exhaust system vibrating.

User Avatar

The procedure is covered in your owner's manual. If you don't have one you can download a .pdf file.

User Avatar

The button is just to the left of the steering column at the lowest point of the dash. It points straight down. --Ken

User Avatar

The keyless entry system must be programmed with an OBD II tool which the dealer or locksmith has. Sorry that this is not the answer your looking for, I didn't want to hear it either.

User Avatar

The regular Outback can tow 2700 lbs. The 3.0R can tow 3000 lbs. When the trailer is equipped with a braking system, if the trailer is not then 1000 lbs. Also be aware that the tongue weight is only 200lbs.

User Avatar

Yes, it is possible to have a keyless lock system installed at home. Keylesslockspro.com and brickhousesecurity.com bot offer keyless lock systems for purchase.

User Avatar

The hazard lights on subarus are located in the middle of the dash not on the steering column like alot of cars check this first, make sure the button is not pushed in, this happens a lot by accident when cleaning the car If this is not it then: If you car has a keyless entry or security system that is most likely the source of the problem. If the battery has been disconnected, it will cause this to happen. You have to find the security or keyless entry system reset button on my 1997 subaru out back it is under the dash on left side it is a black button hold the button in and at the same time turn the key to the on position (Do not start the car just turn to the on position) for about 20 seconds and it will reset

User Avatar

That depends on which system you have. Instructions are on page 3-23 of your owner's manual. If you no longer have your owners manual there is one at the related link.

User Avatar

I have a subaru outback 2001 LL BEAN and I don't know if mine has VDC or where to find the button to turn it on. ***** The VDC(Vehicle Dynamics Control) System works in conjunction with the ABS and the TCS(Traction Control System). It will automatically come on when you hit hazardous road conditions or if you make a sudden move, and will automatically go off when things are back to normal. So "you" don't turn it on, and "you" don't turn it off.....

User Avatar

Follow the written directions that came with the new keyless entry system - OR - take it to the Saturn dealership for programming. The have all the necessary equipment and proprietary software for doing that task.

User Avatar

Subaru has been building the Legacy Outback since 1995. Many changes in the control systems have occurred over those years. Newer models do not have a separate cruise control system, it is controlled by the ECM. On those models the cruise control is deactivated when the check engine light is on. If you care to provide more information we may be able to assist.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.