Chevy Tahoe
Chrysler Town and Country

How do you program a 2009 Chrysler town and country keyless entry remote with only one working key?

123

Top Answer
User Avatar
Wiki User
Answered
2010-01-26 11:52:26
2010-01-26 11:52:26

That requires the dealers scan tool.

001
๐Ÿ˜‚
0
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Related Questions






You need a working key. You will need to have the dealer or a locksmith cut and program a new key.You need a working key. You will need to have the dealer or a locksmith cut and program a new key.


Turn the ignition from OFF to RUN 8 times within 10 seconds, ending with run on the 8th time. Within 20 seconds press any button on a working keyless remote. Within 20 seconds, press any button on new keyless remote.


You need to check your thermostat, pretty cheap fix


the carshop, in alhambra. They Fix my HOFCO 3 remote, one of the buttons was not working. And the also program it for me.


The keyless lock might stop working on your Mitsubishi Lancer because the battery is dead or because there is a problem with the wiring. You might also have a problem if the brain or computer of the vehicle is damaged.


Yeah, it does, but mine isn't working and I'm not sure why.


works sometimes, but no all the time


If it isn't not working, then it must be working properly.


Sadly this is gonna require a visit to the dealer. Plan on spending $40 or so to get this done. Every Jeep from 1996 or so onward will need a dealer program to get keyless working.


Thanks to no help from Chrysler or Dodge....I ended up figuring this one out for myself. I hope this will help you out. Start your Durango and leave it running for about two minutes. Once you do this, press both the lock and unlock button on your keyless entry (key fob) and do this three times, each time holding it pressed down for about two seconds each time. After this, your keyless entry should be reset and working. This had to be done on my Durango after I changed my battery.


Thanks to no help from Chrysler or Dodge....I ended up figuring this one out for myself. I hope this will help you out. Start your Durango and leave it running for about two minutes. Once you do this, press both the lock and unlock button on your keyless entry (key fob) and do this three times, each time holding it pressed down for about two seconds each time. After this, your keyless entry should be reset and working. This had to be done on my Durango after I changed my battery.



Are either of your fans working? If both are not working then there is a separate relay for the fans that is located under the air filter attached to the metal frame.


Check for a recall on the clock spring. If your CD player and horn aren't working, or if the Air bag or ABS light is on, its almost surely it.



use your key and reprogram your remote from the dealership


The tachometer may not be working on a 1995 Chrysler LeBaron because the cable may be bad. Check to ensure the cable is not broken or kinked.


Check fuseCheck to see if you are getting power to it - if so, bad blower motorIf not bad switch?


I had the same problem...it was the "computer". I had to hit the dash for about a year, then it just stopped working. It was around 800.00 to fix. You need to do at a Chrysler dealer as they have to input the codes that your local mechanic will not have.


check fuses if no luck check the brake pedal switch down under the dash by the pedal or check for a loose ground


If you didn't bench bleed the master you need to do that before you install the master.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.