This the programming procedure for a 2000 Corolla and Chevrolet Prizm(same car different name)
Transmitter Programming Reprogramming the Remote Control Door Lock Receiver
The vehicle comes equipped with two transmitters. The receiver can be programmed to accept up to four transmitters. Additional transmitters are available. If the number of transmitters programmed exceeds four, the previously programmed transmitters will be erased in order, starting with the first transmitter. To program a transmitter, there are 3 modes within the remote control door lock receiver. Add mode: This mode is used for adding new or additional transmitters, Rewrite mode: This mode is used to erase all of the previously programmed transmitters and should be used when installing a new receiver, Confirmation mode: This mode is for confirming how many existing transmitters are registered before adding any transmitters. To begin programming, follow the procedure. Set the following conditions: Ignition off and ignition key out of cylinder. All doors closed except driverï¿½s door. All doors unlocked. Insert the ignition key into the key cylinder momentarily and remove it. Using the switch in the driverï¿½s door, move the switch to LOCK-UNLOCK 5 times at approximately 1 second intervals within 40 seconds. Close the driverï¿½s door, then open it. Again, move the switch to LOCK-UNLOCK 5 times at approximately 1 second intervals within 40 seconds. Insert the ignition key into the key cylinder. Turn the ignition switch from ON-LOCK at approximately 1 second intervals for 1-3 times according to the desired mode. 1 time for add mode 2 times for rewrite mode 3 times for confirmation mode Remove the ignition key from the key cylinder. If the add or rewrite mode has been selected, the doors will lock-unlock once or twice at 1 second intervals, once for add mode or twice for rewrite mode. If the confirmation mode is selected, the doors will lock-unlock 0-4 times at 2 second intervals to inform the technician of the number of transmitters programmed. Press a transmitter button for 2 seconds, The doors will lock-unlock once at a 1 second interval to inform the technician that the signal has been received from the transmitter. Close the driverï¿½s door, then open it. Press a transmitter button for 2 seconds, The doors will lock-unlock once at a 1 second interval to inform the technician that the signal has been received from the transmitter. If the doors lock-unlock once, the transmitter programming has been completed. Go to step 9 to continue programming for additional transmitters. If the doors lock-unlock twice, the transmitter programming is not complete. Go to step 9 to begin the transmitter programming again. If any of the following conditions occur during programming, the remote control door lock receiver will return to normal operation: The driverï¿½s door remains closed. 20 seconds elapses with no input to the RKE module The ignition key is inserted into the key cylinder.
The dealers scan tool is required.
See FOB PROG on page 2-19 of your "Owner's Manual", under Section 2: Features and Controls - Keys.....
How do you program a key fob to a 2003 Chevy Malibu
That depends on the problem. If it's just a battery problem, replace the battery and follow the instructions on the inside of the fob. If the fob has failed, Saturn requires that you take it to a dealer to program the replacement fob.
To program any kind of key fob you have to take it to a dealership.
How do I re program my key fob for renault laguna estate 1997?
You don't. Take the car and the new fob to a caddy dealer or a locksmith who has the equipment to program it.
Open the FOB and find out.
A scan tool is required to program a fob on a 2006 Chrysler Town and Country.
To add a new key fob, take the vehicle and the key fob to an authorized dealer. To re-program a key fob after replacing it's battery, open the key fob, then read and follow the instructions inside.
How do you program the remote key fob on a 2005 Chevy Malibu maxx
See "Programming the Transmitters" on page 10 of chapter 2 "Keys and Doors" in the "OWNER'S MANUAL".....
It is possible to program one key fob to use on two different cars. If the key fob uses a primitive fixed code system, programming two cars will not work.
The dealer scan tool is required.
The key fob programing requires the dealer's scan tool.
The key FOB allows the user to open the doors of their vehicle when within a given range. This FOB can be programmed by going to the Ford dealership.
go to corvetteforum.com and they have the answer
You will need a scan tool to program this Keyless Fob.
You must take it to the dealer to have them program it to your vehicle.
So far its pay the Dealer $68.There got to be a salesman out there who knows and would answer this for a car buyer referal.
Due to the fact that it is so early in the model year for vehicles, 02/13/2011 at the time of this writing, the instructions for programming the FOB' or REMOTES for you Chevrolet Impala is not yet available. I am working with a member of a local Chevrolet dealership to develop step by step instructions on how to successfully complete this task. Once developed and tested I will enter the instructions on this web site.
Available at the dealer, he will have to program it.Available at the dealer, he will have to program it.
trying to set up and program 2003 Nissan altima key fob