**Useful tip:
On your first attempt, program a frequency with a high amount of traffic or one that is always broadcasting (such as your local NOAA weather channel) to be sure that you have followed the directions correctly on your first run-through and are confident in being able to repeat them.**
1) Press "Manual" key. Scanner channel indicator should stop scanning and remain lit on one channel. It does not matter which one, as you will select the channel to program in another step. To keep things simple, you might want to use the "Skip" key after pressing "Manual" to light up the channel you are planning to program. This is not necessary but does keep the channel you are programming and the channel displayed on the panel the same, possibly eliminating confusion.
2) Program the desired frequency by using the number keysand period (.) key. Be sure you hear a beep after each keypress. If you do not, the number was not accepted and you will have to press it again. Also, this scanner only allows up to 3 digits on either side of the period (.). I.e.453.975 would be valid, while 460.6125 would not. See end of instructions for valid frequency ranges for this scanner.
3) When you are done entering the desired frequency, hold the "Enter" key until a beep is heard. Release "Enter" key once beep is heard. Channel selector light will now be flashing. You may also hear radio traffic on the entered frequency at this point if someone is transmitting on that frequency. If you attempt to program a frequency NOT supported by the R1060, the scanner will constantly beep at you. At this point you can enter another frequency using step 2 (while it is beeping.) To exit programming mode while it is beeping at you, press the "Skip" key. See end of instructions for valid frequency ranges for this scanner.
4) Press the desired channel you wish to store this frequency in (1-10) using the number keys. To store in channel 10, press and hold the "0/10" key. As with the step above, hold the desired number until a beep is heard. Release key after beep is heard.
5) Channel is now programmed. If you attempt to enter a frequency not supported by the R1060 your changes will not be made and the channel will either be empty or will revert to the previously stored frequency. I have seen both happen (perhaps some units had different operating characteristics during it's production run).
This scanner's programmable frequency range is:
30-50MHz / 146 - 174MHz / 450 - 512 MHz
The frequencies listed are the ranges available on every factory production unit.
These ranges are modifiable with easy to replace crystals made specifically for this unit. Where to obtain these is beyond the scope of this article.
Add your answer:
How do you program a regency scanner model R1040?
Programming scanner r1040
What is the programming sequence for a Regency D300 scanner?
How do you program regency d300. the model number d300.
How do you program a regency scanner model r1075?
Hit manual til u get to the channel you want to program and type in your freq. and hit enter
How do you program a regency scanner model R2060?
You simply press manual on the desired channel to program. Enter the frequency and press enter. You cam set the channel to be delayed (so it doesn't start scanning again) at any point. Hope this helps.
How do you program regency scanner model r1077?
One should program a Regency Scanner with the model number r1077 by first turning the device's power on. Then press the manual button until the channel wanted is shown. Once the channel number is shown hit enter, which will make the frequency channel that number. Then one can go to the next channel number and hit hold, or delay, to hold the number for dispatch. In order to lock certain channels one should hit the lock button when the channel number comes up instead of enter, and this will keep that particular channel locked.
What scanner is needed to program a keyless entry remote?
The car is the scanner. Depending on the make and model a new key less FOB can be programmed by pushingcertain buttons on the car in a certain sequence. What year make and model are you trying to program.
How do you program a Croba Police Scanner Model SR900?
Press the manuel button then press the channel number you want to program and then press the manuel button again. Press the frequency numbers in t\and then press the "E" for enter. Now your police scanner is programmed. :)
How do you program a model bc80xlt scanner?
Follow the link below to download/print the manual for your scanner. It will walk you through the programming process: http://www.uniden.com/pdf/BC80XLTom.pdf
How do you program a Cobra Police Scanner Model SR900?
Programming the Cobra SR900 Power the scanner up. Use the "manual" key to select the channel to be programmed. Press the "E" button, then enter the frequency (you want to program in) and press the "E" key when you are done. Press "manual" to select the next channel and repeat.
A benefit of a model EEO program is?
A benefit of a model EEO program is?
What model OBD 2 diagnostic scanner is compatible with a 2000 Ford Windstar?
Any OBD2 scanner will work.
How can you create an email configuration to connect my scanner to PC?
Usually you can find that information on the manufactures website. What brand and model scanner do you have?
How much is the Weight of a 1992 Oldsmobile 98 regency?
depends on the model. Is it a delta 88, or an achieva, or what!
Where can you buy crsytals for regency model act-r-106?
EBay is about the only place these days
Scanner Repair?
form_title=Scanner Repair form_header=Whether your tech repair need is big or small, a professional repair service can help you fix it. Brand of scanner?*= _[50] Model of scanner?*= _[50] Has your scanner been dropped or damaged due to water?*= () Yes () No Is your scanner under warranty?*= () Yes () No What problem(s) are you experiencing with your scanner?*= _Please Explain[100]
Who is the brunette in the neatdesk scanner commercial?
Liz from top model
You have 1998 gmc truck 1500 5.7cam retardwill a scanner work?
You have to use a scanner, A timing light will not help at all. there's no way to use a t-light on a 98 model. Scanner only.
Where can you download software for Fission Film strip scanner Model GFP-001?
From punjabu rap
What are the best name brand computer scanner accessories?
HP makes a very good scanner model. EPSON is good to and high quality ink.
Why wont the scanner power up when hooked to a aldl on 96 corsica 2.2?
A 96 Corsica uses OBD2 as required by law for 96 model years. Use an OBD2 Scanner.
What driver does a scanner need?
Drivers are specific to the model; different scanners need different drivers.
Can I hook a scanner up to my LCD t.v.?
There are some scanners that you can hook up to LCD tv's but it all depends on what kind of model and make both the scanner and tv are too see if they are compatible.
How do you use a zebex scanner model z-3110?
You need the programming guide from ZEBEX and the Buyer guides.
How do you replace the voltage regulator in an 98 Olds regency 1986 model?
The voltage regulator is an integral part of the alternator. I would recomend replacing the alternator.
Where can you find information on a Firearms Interational Regency model 22 LR cal revolver marked made in US?
Blue Book of Gun Values
Get the Answers App
