if you have forgotten the order of the wires, go to a dealer(Buick,or gm)or perhaps the library to find the proper sparkplug wire diagram. if you havent misplaced the order you simply push the plug until it clicks
Also call your local parts store,tell them you need the firing order.Its best go in person as most times they have diagrams in books already.I always make a written diagram and mark the wires with tape and numbers.
It is located where all the spark plug wires attached to the spark plugs go to it.
Check firing order Two of the plug wires are crossed.
To replace spark plug wires on a 3300 Oldsmobile engine, open the hood and remove the wires from the end of the engine. The number of spark plug wires most often corresponds to the number of cylinders your engine has.
check to see if the spark plug wires are fireing
no comment i just need the answer where is the number one spark plug on the 307 distributor cap
Could be in need of a tune up. Start with replacing the spark plugs and spark plug wires.
The cooling fan on a 1993 Oldsmobile Delta 88 is located behind the radiator and the wires are attached on the left hand side. The relay is located on the frame near the left headlight.
Spark plug wires. spark plugs or fuel filter. Check and rpplace them in that order. Usually only spark plug wires need replacing.
disconnect the battery, then the wires from the starter. Then remove the bolts holding the starter to the engine.
how do you put spark wires in the right place on the coil pack on a 1995 Chevy cavalier2.2 frank
how do you know what wires to connect on your spark plugs example1-6 2-5 3-4 and how do you know which spark plug is 1 2 3
It should be under the spark plug wires connector block.
At the top area of the engine, look for thick black wires (kind of rubbery to the touch) those wires meet in a plastic cap (all of them) that is called the distributor cap, the other end of each of those wiores end in a spark plug, follow them, it's easy. good luck
You will need to change the Oil and filter, spark plugs, spark wires, fuel filter, air filter, oxygen sensor, thermostat, drain flush and refill the cooling system, and (if needed): change the breaks, rotate the tires, and change the transmission fluid.
You do not have to but it will be very good if you place a die-electric grease on points where ignition wires contact spark plugs and distributor/coil pack.
you would take out the spark plugs still attached to the spark wires. place the metal of the plugs onto a grounded metal spot. make sure they are not touching in order to prevent damaging them or blowing fuses.
The spark plugs are on the front and back of a V6 (back ones are tough to get to) L4 right in front. Turn the engine off and take off the spark wires unscrew the plugs
it is located at the front of the engine under the coil packs(where the spark plug wires all connect)
Disconnect the battery, remove the spark plugs wires and boots and remove the spark plugs. Put in the spark plugs, replace the spark plug wires and boots, and connect the battery.
in the cylinder head, underneath the spark plug wires, same place they are on EVERY VEHICLE EVER MADE
There are electrical wires all around the vehicle. If you are looking for spark plug wires, it does not have any. It has individual coils directly on each spark plug.There are electrical wires all around the vehicle. If you are looking for spark plug wires, it does not have any. It has individual coils directly on each spark plug.
Get the proper replacement wires. One end goes on the spark plug and the other goes on the distributor cap. They are connected to the distributor cap in order,so do not place one out of sync.
The spark plug wires on your 1994 Chevrolet Caprice are quite easy to change. The spark plug wires simply lift off on each end. Put the new spark plug wires on and push until you feel a click.
Pull the spark plug wires off the spark plugs. Remove the spark plugs with a spark plug socket. Install the new spark plugs and put the spark plug wires back on. I recomend replacing the spark plug wires as well. If replacing them, just remember that the new wires are hooked up the same ways that the old ones came off.