Auto Parts and Repairs
Spark Plugs and Wires
Dodge Caravan
Dodge Grand Caravan

How do you reach the rear set of spark plugs on a 1995 Grand Caravan to replace them?

303132

Top Answer
User Avatar
Wiki User
Answered
2015-07-15 20:58:14
2015-07-15 20:58:14

i find it easier to go under and around. Haveing a pit really helps with this.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


you need to replace your fan relay switch, in my 2000 caravan i had to remove thel left head light to reach it

Yoiu have to reach around the intake plenumn from the top.

you will have to go under.raise it up ,put some jack stands and reach up!

The fuel filter for the 2001 grand caravan is located above the gas tank, in order to change it the gas tank may have to be lowered so you can reach it.

On replacing the tensioner you first must raise the van up to get under it, you can reach it better you wil need a long extension & swivel and 15mm socket.

Tune ups on modern computer controlled cars amount to new plugs and wires every 100,000 miles. There is no distributor cap, rotor, or points like older vehicles. I wanted to replace the plugs on my 1998 GP until I discovered that you must remove the rear engine mount and jack the engine up to reach the rear plugs.

To change spark plugs on a 1994 Toyota Camry, remove the black shafts. The spark plugs are down the four holes. Use a socket set with extension to reach the spark plugs. Replace old spark plugs with new ones.

you can reach them by removing the tires and the wheel well guards [plastic]

reach up between the grill and the radiator/ac cooler and pull on what's left of the cable.

You either have to reach from underneath along the exhaust to access, or you have to remove the wiper cowl to access.

hi there,to replace the rear spark plugs you virtually reach over the motor and do everything by feel .it is quite an awkward reach to get at them,but the hardest one is the one closest to the drivers side. there isn't much room.if it helps you can also hang a small mirror there and this helps a bit to see what you are doing.hope this helps. Dave

You must remove the 3 bolts on the opper part of the headlight housing and then remove the entire housing. You can then reach the bulb connection

I reach over and around the top of the engine to access the spark plugs.I reach over and around the top of the engine to access the spark plugs.

..internal..i belive it is behind the timing belt, passenger side...big job ...or if you have the model i have it's so easy (Grand Caravan 2000 3.3l SE), it's located on the passange reach from underneath, i think originally there is a mud cover you have to take off and you'll have access to it

I just replaced the tensioner on my 1998 dodge grand caravan. One could reach from the back but would need a lot more dexterity along with small arms to reach it. When I replaced mine I simply took off the alternator and removed it. With the alternator out of the way I used a socket wrench and reached over the top of the engine to access the tensioner nut. One has to do a little blind work but if you can get passed this the whole thing should only take about 15-30 minutes. The easiest way is to jack up the van and reach through the back, you can also do it 'blind' if you have good wrist flexibility

Jack up the front remove front tires, move inner splash guard reach in with a LONG extension, remove and replace plugs

It is your choice. You can either remove the transmission and leave the engine alone. or pull the engine and leave the transmission alone. If your SMART you will replace all the freeze plugs in the engine.

Front bank of plugs are easy. Back bank of plugs are more difficult but can be reached from the right side(drivers side) of the engine. Make sure engine has cooled before attempting to reach in behind the engine...thereis an exhaust manifold and shield there which can be very hot.

i have an 03 aztek. i change plugs myself, i have skinny arms to reach from underneath the car.

upstream will be in the manifold, downstream refers to behind the converter Upstream o2sensor on exhaust manifold . from underneath have to reach up to where meets up with block. hard to reach . but not impossible

The hardest part is getting to them. You have to be able to get clear access to the freeze plugs. There are typically several, and often there are a some that are difficult to reach. You'll need to look at a reference manual to see where they all are. Sometimes you have to pull the engine to get to the freeze plug that is under the flywheel/flex plate. It depends where the freeze plugs are located. I just recently had the rear plugs replaced on my ranger v6 3.0 and you cannot reach them. I had a shop do the work and instead of lifting the engine out they dropped the transmission and was able to reach them from underneath.

I just changed the whole headlight assembly in my 1997 grand caravan. However, to change the parking light or turn signal indicator light, there is a round plastic plate in the front fender well in front of the tire. Pop this out and reach in and unplug the socket from the light assembly, change the bulb and install in reverse order. Good luck!

I recently asked the same question on a similar sight. To replace the back spark plugs you have to reach them from under the vehicle. You will be working blind the entire time, so plan on several hours to complete the project.

Drain the radiator. Remove the heater hoses from the fittings at the firewall under the hood. Loosen the dash, and pull it out enough to reach under to the heater core. unbolt the core, remove, then replace. Reverse the procedures to finish the installation.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.