Fuel Filters
Ford Ranger XL
Ford Ranger XLT

How do you release pressure in the fuel lines on a 1993 Chevy S-10 blazer?

555657

Top Answer
User Avatar
Wiki User
2011-09-13 06:11:57
2011-09-13 06:11:57

there is always a pressure release valve to remove air for fuel,location is usually on the right top of the motor where the fuel lines come in from the tank. the valve looks like the valve from your tire. just use a nail or something similar to press the valve and air will release then fuel will flow. and don't forget it has a cap.

Answerpressure is usually released by just opening gas cap.
1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

should be unless it was removed and lines plugged off (not a good idea)

User Avatar

The brake lines can be replaced by removing all of the retaining clips. The brake lines will need to be disconnected on both ends. Reverse the process to install the new brake lines.

User Avatar

on the top of the transmission its on the transfer case with 3 vacuum lines coming out of it.

User Avatar

It's lean. Best to check the carb and all vacuum lines for leaks and blockage.

User Avatar

Find the part that needs to be replaced and do what u need to do to get it off if then put the new part on :)

User Avatar

They may be marked "S" and "D" for suction (low side) and discharge (high side). A simpler way would be to look at the lines going into and out of the AC.... the smaller line will be the high pressure line, while the larger line will be the low pressure line. The low pressure line will connect at the compressor inlet, and the high pressure line will connect at the compressor outlet.

User Avatar

at a salvage yard & some auto parts stores ----- if you omly have a hole you can get a splice kit at auto zone

User Avatar

fuel problem. make sure you have gas of course, check out your fuel pump, injectors, fuel lines etc.

User Avatar

Depending on the year, the blazers fuel filter is most likely on the frame. While covering the connection with a rag, loosen the fuel lines from the filter. Remove the filter and replace, then reconnect the lines.

User Avatar

The fuel lines around the filter; you will need an adapter.

User Avatar

You need a quick release tool to remove fuel lines. You can pick one up at any parts store.

User Avatar

If your engine is a 4.3L V-6 with CPI (central point injection) it is inside the upper intake manifold. The upper intake manifold is bolted on top of the normal intake manifold. The throttle body is mounted on it and your fuel lines terminate into the center of this.

User Avatar

Follow lines from compressor-Larger line is low pressure--port may be at or around the accumulator/drier by passenger firewall

User Avatar

Master cylinder brake lines are the most common brake lines on a the Chevy Malibu.

User Avatar

You will have to put it somewhere warm.

User Avatar

It is inside the upper intake manifold. To get to it you must remove the throttle body, upper intake manifold, and several electrical lines and fuel lines.

User Avatar

The lines on a map for pressure stands for Isobars which they are lines on a map around areas with the same pressure readings to indicate highs and lows.

User Avatar

The 4wd in the 1999 Chevy blazer is electronic, you just have to push the button. If you have pushed the button and it doesn't engage, it might be a vacuum line. The lines are made of rubber and over time they melt. It costs about $25 for a new metal line. Also, the 4wd is under the battery. If you take the battery out, you might notice that a line got disconnected accidentally.

User Avatar

I need a lay out of all the vacuum lines for a 1991 Chevy van.

User Avatar

there are straps that bolt to the frame loosen them and disconnec the fill tube, pressure, return, and vent lines and lower it carefully

User Avatar

with the ignition switch OFF, break the fuel lines loose slowly. there may be some fuel leak out, but that is normal.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.