First you have to pull apart the gray console around the radio with any flat thing like a screwdriver, then just unscrew two bolts in the corners of the radio. X. V.
www.installdr.com will tell and show instructions for everything
Remove the ashtray, then remove the screws behind it. Carefully pry the plastic molding off (that surrounds the radio) using only fingertip power. Remove 4 screws holding the radio in.
i dont know oem is original equipment manufacturer that means a factory installed radio
Exchanging an OEM single CD radio with an OEM 6 CD radio is a simple upgrade which requires the use of a proper wire harness to ensure radio usability. Once the stock radio is removed from the dash the 6 CD changer will plug right into the proper OEM wire harness.
It will be 14 or 15 inch depending on the particular model you are referring to. The OEM size is listed on the drivers door post.
it should be on the trunk compartment, driver side, behind the carpet, its the only module there. This apply only for the OEM alarm module
There are many places where one can purchase a Ford OEM radio for their car. One can purchase a Ford OEM radio for their car at popular on the web sources such as the official Ford website or Amazon.
Remove the trim panel around the radio, it just snaps in. Then there are 2 bolts that hold it in. They are 10mm. Once removed just pull the radio straight out. You may need to giggle it a bit as it is a close fit. Remove the 2 connectors and the antennae wire. You're done.
stock oem or after market radio all radios have diff. keys. but you can remove the whole thing by pulling the plastic bezzel around the radio, pop. then you see all the screws. remove them and out it comes. remove ash tray and its holder see more screws.
OEM equipment modifies the audio from the radio, sends it to the speaker and converts it back to normal audio on the speaker frame ckt board. To put in an aftermarket radio, use two of the wires and connect up to your new speakers and radio to make use of OEM wire routing.
Had mine done about a year ago (April 2009) for around $425 using OEM struts. 2004 SRT-4
Removing the radio from a 1990 Cressida is a pain, mainly because it is in three parts (radio/CD player, radio/CD player controls, and amplifier). First you remove the trim from the transmission shift area, then begin removing all the plastic items from around the radio and control strip, working your way up from the shift area. Note that you will probably not be able to replace the OEM radio --Toyota wants $2300 for one, but they don't have any. If you install an after-market replacement radio you'll have to rewire the speakers, because they are connected to the separate amplifier, located behind the radio on the firewall, which can only be controlled by the OEM system. Note also that if you install an after-market radio and you bypass the OEM radio controls (you'll have to leave them in place, or you'll have a gap in your dashboard), you'll need to be sure to reconnect the emergency flasher, which is located on the control strip. Good luck!
It displays on the factory radio. There is a button on the OEM radio to either show the time or radio station.
All you need is an adaptor
yes, they are the exact same car. the only difference are the names dodge and plymouth, which are both owned by chrysler. LMAO, WAS THIS A SERIOUS QUESTION? Depending on your VIN number, they are NOT the exact same. I, for one, have a 2000 PLYMOUTH, and the CLUTCH is VERY different than a dodge. you have to order SPECIFIC parts designated to that very VIN, for example, a hazard relay, has to be OEM, or it's gonna blow your crap. YES, it will fit.
Yes, they can be replaced separately from the control arms. Moog make OEM replacements or if your looking for an upgrade there are several performance MFG offering products as well.
Listed on the driver's door post. The OEM size for the Ram 1500 2wd is 225/75-16.
yeh but it will be well chavy
You buy a new operating system and install that.
try looking at tss-radio.com these guys have everything you could ever want for sirius, even the radios!
Replace it with an oem replacement line.
it is oem and ecm on 2002 dodge caravan Internal computer failure.
Champion # RC 12LC4 .040 inch gap
I'm not sure what a mechanic would charge to replace it... but I found the part at www.Autozone.com. Duralast / Camshaft Position Sensor For your 2004 Dodge Neon 2.0L SFI SOHC 4cyl Part Number: SU3020 Ref: OEM Number: 4667745; 4778796; 4882850; 4882850AA; 4884111AA; 5096057AA; 5235378; 6034887 $25.99 / 2Yr. Warranty The camshaft position sensor is mounted to the rear of the cylinder head.
As long as you use an OEM unit, it should plug right in with no modifications necessary.
first you have to pop the door panels off then unscrew the stock speakers and pull them out then there should be aclip on the back side of the speaker pull the clip off and if your replaceing it with oem speakers just clip in the oem speakers but if your gonna use no oem sppeakers/ like wal-mart car audio speakers you have to cut the clips off and wire it to the prongs on the back of the replacement speakers.