Find all the clips, then pull them off. There should be 2 or 3 screws on each side.
This video on YouTube (see Related Links) will show you how to remove the front bumper cover from of a 2004-2007 Honda Accord.
Headlight cover? The headlight can be removed by first removing the bumper cover. THen all the bolt that attach the headlight to the vehicle will be exposed. The "cover" is glued to the headlight housing.
Depends on if it's just the cover and if you do the remove and replace yourself. I did a 2008 Civic rear bumper cover for $250 (real Honda part) + $260 for painting. Took me about 1.5 hrs total - had to put the back of the car on stands , take the rear wheels off, remove the mudflaps, undo 6 bolts and remove the old one. Install was the reverse - needs 2 people to handle the new cover.
You have to take out the bumper. Just take out the screws that are in the fender, take out the plastic cover that it is under the car that is attached to the bumper, take out the clips of the plastic grille with the Honda logo and pull the bumper. Don't apply to much force. When the bumper is out you will see the other bolts to remove the headlight.
You need to remove the bumper cover in order to get at the lower bolt for the headlight assy.
remove your the cover off the door panel to get to the stero.make sure u unplug it
Remove the screws in the wheel wells and underneath the plastic cover to remove the bumper cover. Then you can see to remove the actual bumper.
nightmare. you have to remove the front bumper cover. then you will see the bolts holding the lamp assembly.10mm socket
remove the bumper, you will then see the bracket that holds the bottom of the light to the car. the rest is pretty self explanitory once the bumper cover is off
Hi, to fix as in put a brand new bumper cover and paint job costs close to $500 dollars. i fixed my bumper for 250 with paint job because i knew some people bumper of course was aftermarket.
The steering wheel cover on a 1991 Honda Civic DX is held on by several mounting screws. Remove all the hardware and the steering covers will just pop off.
REMOVE TWO TOP BOLTS ON HEADLAMP ASSY. THEN REMOVE BUMPER COVER, THATS RIGHT THE BUMPER COVER, THEN REMOVE TWO BOTTOM BOLTS
A 2004 Honda rear bumper cover can be made to fit a 2007 Honda Accord. However, the amount of helper parts to make this fit happen will cost more in the end than it would to have just bought the bumper outright.
it clips on to the base by little "hooks" on the outer edges
A Honda Civic rear view mirror is held in place by screws. To see the screws remove the plastic cover. Loosen all the screws and the mirror will drop down. Replace with a new unit.
pop off cover and then use Phillips head screw driver to remove the three screws and you are done
To remove the rear bumper cover on a 1993 Ford Taurus wagon, the lights need to be disconnected in the rear. Once all electrical connections are disconnected in the rear, remove the taillights and the fuel filler overflow hose. Remove any nuts and bolts holding the bumper cover on. Using needle nose pliers, pop the push pins around the bumper cover upwards. Slowly pull on the bumper to remove it.
The taillight bulbs can be easily replaced on a Honda Civic. Open the trunk and locate the plastic covers. Remove the plastic cover and pull the bulbs. Replace with new bulbs and install the covers.
You must be a woman. Remove the oil fill cap on the valve cover and put 4 quarts in.
Yes, if they are both the same generation.
I do not believe there is a metal bumper. There is a foam insert that goes inside the bumper cover.
Unbolt the front of the wheel well liner inside the wheel opening.Remove the bumper cover bolt from the bracket located inside of the bumper at the end.AT the front of the car, remove the bolts holding the bumper cover on, located underneath the vehicle.You should now be able to remove the bumper cover from the front of your Dodge Intrepid.An instructional video has been included to show you the removal process.
The fuel pump is in the tank, but to getting to it is easy. You remove the back seat and there will be a metal cover that you remove. After you remove the metal cover there will the bolts holding the fuel pump onto the tank.
from underneath the vehicle u have to remove some suspension parts and parts of the front cover of the engine
# Apply parking brake,raise the vehicle and secure it # working under the vehicle,detach the fasteners securing the lower edges of the bumper cover # Working in the front wheel opening,detach the retaining screws securring the bumper cover to the inner fenderwell splash shield # Pry out the lower edge of the splash shield,then reach up behind the bumper cover and remove the bumper cover fender retaining nuts # remove the fasteners securing the upper portion of the bumper cover and pull the bumper cover assembly out and away from the vehicle. # Disconnect any electrical connections which would interfere with removal