Hey Sherri==It is best if you go to Auto Zone or another parts store and get a manual on your car for about $18 and it will show you with pictures and everything. You can go to AUTOZONE.COM nd install your car and go to REPAIR INFO then to PRODUCTS AND HOW TO then to "S" for starter and then to REPLACE. These are fairly good directions but are pretty generic. Lots of luck, Joe
On 98's the starter is on the radiator side of engine...best way to remove as I have found out myself...
Remove the two Radiator fans... and remove the top hose on radiator then you have easy access for your hands to reach the starter... then remove the battery and battery box...that will expose the two bolt heads on the engine block, just line yourself up with the starter than you will be able see which bolts they are...There are quite a few of them for other things on the engine... once bolts are removed then you can take the starter out after the hot and the ground wires are dissconnected... Put new starter in reverse order of these instructions... Average time about an hour or less depending on your level of proficency ... Oh the new starter would cost close to a hundred dollars because the starter and solenoid is together as one unit... I recommend a second hand used starter that has been tested from a Junk Yard dealer ... That is what i did for my customer that i done this on recently to safe her money that she can't really afford for a new one...I think i have just about covered all i know on this one...
are there 2 bolt ot 3 bolt on a starter on 1998 neon
HOW TO REPLACE A STARTER ON A 1998 CHEVY MALIBU
Remove the positive cable from your 1998 Saturn battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.
Remove the positive cable from your 1998 Monte Carlo battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.
Even if it is possible it would be much easier to remove the starter and replace the selenoid with the starter on the bench. Your best bet would be just to buy a remanufactured complet starter assembly and replace the whole thing.
Disconnect the - battery cable Raise and support vehicle Remove wiring at top of starter Remove starter mounting bolts Remove starter
Remove the positive cable from your 1998 Chevy Cavalier battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.
how do you replace a starter on a 1998 cutlass
YOU FIRST HAVE TO DISCONNECT YOUR BATTERY. # Remove air duct assembly. # Disconnect starter harness. # Remove starter bolts (two). # Remove starter. #
Remove - battery cable Raise and support vehicle Disconnect wiring at top of starter Remove starter mounting bolts Remove starter
The starter on a 1998 Toyota 4runner is held located on the transmission housing. The starter is held on by 2 bolts which mount it directly it the engine. Remove the two bolts to replace the starter.
replace the starter on a 1998 Chevrolet cavalier
were can i locate and replace a starter for a 1998 buick regal?
No. The engine mount may be in the way depending on the engine.
You could push start it but I would advise against it as the P/S & P/B would not work and you would have to get the vehicle up to around 35 mph. Why not just remove and replace the starter?
For safety reasons remove the positive cable from the 1998 Ford Aerostar battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.
Located in the fuel tank -probably have to remove for access
disconnect the battery, pull the primary cover and remove the jack shaft, You will need a 1/4 Allen socket to get to the starter bolts. remove battery pos cable from starter and remove
Remove negative cable from battery Disconnect positive cable from starter and ignition wire Loosen mounting bolts from starter Remove starter Install new starter in reverse order of removal
Dont Change it
locate starter, mark and remove wires, remove bolts, remove starter
You can replace the timing belt on a 1998 Plymouth Breeze 2.0 engine using a Harmonic Balancer Puller 5.
you need to remove the left primary case and remove the gear from the end of the starter shaft. then you can remove the mounting bolts and the starter will slide out.
where is the starter located on the Audi a6 quattro