there are screws under the handle and 2 at the bottom of the door panel. you will need to remove the window crank if you have one, and all u have to do then is remove the clip from behind the handle. if its power then all u have to do is unplug it from the back when u get the panel off. dont worry about being gentle there are plastic pins that hold the panel after you have it undone.
Removing the door panels on a 2000 Ford Ranger is easy. All you have to do is snap out the old panels by unscrewing the bolts and screwing in the new ones.
Go to this website. It will show how to remove the door panel.
The 1998 Ford Ranger door panel has eight retaining clips. Pry outward on each retaining clip. Remove the two door handle screws.
remove the window handle, remove screws from armrest, remove the inner door handle and the screw on the lower rear of the door panel, lift the panel upwards to remove from the slots along the bottom of the door.
Pull the door panel off, remove the door latch assembly from inside the door, and replace the switch which is hold onto the latch with one screw on the backside of the latch.
Remove the screw under the door latch
What you do is you fart
Using a screw driver, remove the screws and remove the clips from the door panel. Remove the panel slowly, remove any wire connections, and pull the panel off the door frame.
You will need to remove the screws in the door. They are located in the door handle, the door latch and at the very bottom of the panel. Once you remove the three screws pull the panel and it will pop out.
YOU MUST REMOVE DOOR AND WINDOW HANDLES, ARM REST AND THEN YOU CAN POP THE DOOR PANEL WITH A LARGE SCREWDRIVER OR A REMOVAL TOOL FOR THE PASTIC PUSH IN RETAINERS
To remove and install a door mirror on a 2000 Mitsubishi Mirage, the door panel needs to be removed on the inside of the door. First remove any light lenses in the door, then unfasten the clips holding the door panel on. Then remove the mounting bolt for the mirror. Put in a new mirror, replace the door panel and the light lenses.
remove the screw in the arm rest another one in the corner at the bottom. and then pull up from the bottom of the panel it will lift off it has hooks that fit into square holes.
Remove the door bezel.Remove the window switch.Remove the door pull trim bezel.Remove the 2 7MM bolts behind the door pull trim bezel.Using a door panel tool, you should be able to remove the plastic clips behind the door panel.
just remove it
Remove all the screws. (There are 2 under the "Close Door Handle" Then, simply lift up the panel. David
It has two. One behind the drivers side door panel and one behind the passengers side door panel. I just purchased one for my 2000 Ranger for $10 at my local parts store.
Remove the rear door panel.
You need a flat-head screwdriver and a TORX bit to remove the door panel on a 2000 Corvette. Use the screwdriver to remove the rectangular panel behind the interior door pull. Next, remove the two TORX screws. Pull the interior door handle open and use the small slots to pry off the panel. Lastly, use the screwdriver to disengage the bottom clip and pull the door panel off.
Using a screwdriver, remove the screws from the panel, remove the clips from the panel, and pull the panel away gently. Remove any wiring connectors, and remove the panel from the frame.
Using a screwdriver, remove the screws that are in the door panel, be sure to remove the clips as well, and gently pull the panel away from the frame. Remove any wire connectors between the frame and the panel, and pull the panel off the rest of the way.
The 2000 Buick Century door panel is held in place with for retaining bolts and 10 retaining clips. Remove the retaining bolts and pry outward on the retaining clips.
To remove the door panel on a 2000 Olds Intrigue, remove the lenses off any lights in the door. Then remove the screws holding in the light assembly. Using a screwdriver, gently pop off the clips in the corners and on the sides.