Heater Cores and Blower Fans
Ford Crown Victoria
Ford Ranger XL

How do you remove a heater coil from a 1988 ford crown Victoria?

293031

Top Answer
User Avatar
Wiki User
2006-04-04 17:36:42
2006-04-04 17:36:42

The dash has to be removed to gain access to the heater box. The heater box then comes out and is split open to replace the core.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

WHERE IS THE FUSE BOX LOCATED ON A 1988 FORD CROWN VICTORIA

User Avatar

According to my Chilton's Auto Repair Manual : For a 1988 Ford Crown Victoria : ( 20.0 U.S. gallons )

User Avatar

I believe you can get acess to the fasteners behind the carpet in the trunk.

User Avatar

Drain the water from your 1988 Chevy cooling system. Remove the heater core water supply hoses. Remove the heater core retaining bolts. The heater core will come out.

User Avatar

According to my Chilton's Auto Repair Manual : For a 1988 Ford Crown Victoria : ( 20.0 U.S. gallons )

User Avatar

The easiest and quickest way to change the heater core in your 1988 GMC Jimmy is to remove the water from the cooling system. Remove the water lines from the heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.

User Avatar

It is stuck into the small diameter neck of the evaporator core.

User Avatar

On your 1988 FordLTD Crown Victoria , 5.0 Follow the TOP radiator hose from the radiator to the front of the engine The engine cooling thermostat is in the front of the intake manifold where the radiator hose connects

User Avatar

To replace a 1988 Dakota heater core, first discharge the A/C. Then remove the lower instrument panel before removing the heater box unit.

User Avatar

On a 1988 Ford Crown Victoria : The 5.0 liter / 302 cubic inch V8 is fuel injected The 5.8 liter / 351 cubic inch V8 engine has a carburetor ( so , it is not fuel injected ) According to my Chilton's book

User Avatar

First remove the right front speaker and cover then remove the top bolts in the heater box and the remove the heater hoses out front in the spare tire compartment. Then remove the two straps holding the heater core in place. Reverse order for installation.

User Avatar

According to one of Ford's websites : For a 1988 LTD Crown Victoria , 5.0 liter / 302 cubic inch V8 engine : ( .050 inch spark plug gap )

User Avatar

Check the volts right from the battery, might be a faulty alt.

User Avatar

If you don't have a temp. light, or temp gauge, then just install one.

User Avatar

where is the fuel pump reset buton for 1998 camro V6

User Avatar

Drain the water from your Dodge Ram truck cooling system. Remove the water lines from the heater core. Remove the heater core retaining bolts. Reverse the process to install the new heater core.

User Avatar

A "heater" or a "heater core"?

User Avatar

According to one of Fords websites : For a 1988 LTD Crown Victoria : 5.0 liter / 302 cubic inch V8 engine ( the spark plugs are gapped at .050 inch ) 5.8 liter / 351 cubic inch V8 engine ( the spark plugs are gapped at .044 inch )

User Avatar

About 150 ----------------------------------------------------------------- For the 302 cubic inch ( 5.0 liter ) , 150 horsepower as mentioned above For the 351 cubic inch ( 5.8 liter ) , 180 horsepower For a 1988 Ford Crown Victoria ( according to my Chilton's Auto Repair Manual )

User Avatar

Get a manual on your van fron the parts store or AUTOBOOKSONLINE.COM


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.