Chevy Blazer

How do you remove a ignition lock cylinder from a 1996 Chevy blazer?

171819

Top Answer
User Avatar
Wiki User
2015-07-15 20:05:17
2015-07-15 20:05:17

Start by disconnecting the yellow wire under the dash for the airbag. Now turn the steering wheel 90 degrees to access the underside of the steering wheel. You will have to insert a smaller size flat blade screw driver into the 4 holes on the back of the steering wheel and rotate them to release the airbag. Now remove the nut holding the steering wheel on and remove the steering wheel. BE VERY CAREFUL WITH THE AIRBAG MODULE!! Now remove the lower column cover with 2 Torx screws. You will now have access to 2 inverted Torx screws that hold the top column cover in place. Look on the top of the ignition cylinder housing and find the small hole. Insert a small Allen wrench into the hole and turn the key to "run" position and the ignition cylinder will come out. Hope this helps.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

You will need to attach the wiring harness to the end of your 1984 Chevrolet Blazer ignition lock cylinder. Slide the cylinder into the cylinder slot. Secure the ignition lock cylinder with the retaining ring.

User Avatar

To replace an ignition switch on a 2000 Chevy Blazer remove the lower steering column and dash. Locate the ignition switch and pull the end-clip off the main harness. Remove the mounting screws from the ignition cylinder and replace the unit.

User Avatar

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.

User Avatar

You will need to remove the retaining ring from the top of your 1975 Chevrolet pickup truck ignition cylinder. Slide the ignition cylinder out and remove the wiring harness. Reverse the process to install the new ignition cylinder.

User Avatar

Remove the retaining ring from the top of your 1997 Chevrolet 1500 ignition cylinder. Slide the ignition cylinder out and remove the wiring harness.

User Avatar

You will need to remove the retaining ring at the top of your 1978 Chevrolet Blazer ignition switch. Slide the ignition barrel out and remove the wiring harness. Reverse the process to install the new ignition switch.

User Avatar

You will need to remove the retaining ring from the top of your 1989 Chevrolet blazer ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.

User Avatar

Remove the wiring harness from your 1995 Chevy Blazer ignition control module. Remove the ignition control module retaining screws. Reverse the process to install your new ignition control module.

User Avatar

You can remove the 2000 Chevrolet Astro Van the ignition switch cylinder by removing the retaining ring. The retaining ring will need to be turned to the left. The ignition switch cylinder will slide out.

User Avatar

The buzzer that lets you know the key is in the ignition in a 1989 Chevy Blazer is in the steering column. To access it you would need to remove the steering wheel with a special tool, or remove the ignition assembly. The key makes contact with a tab that activates the buzzer.

User Avatar

Where is the control module located on the 1983 Chevy blazer

User Avatar

How to Remove the Steering wheel From a Chevy Blazer 2001

User Avatar

how do you remove the dashboard of a 2002 Chevy blazer

User Avatar

You would have to drill out the center of the lock or have a locksmith pick the lock.

User Avatar

I broke my key in the ignition and cant get it out. My only option I can see, is to replace to tumbler. How do I remove it?

User Avatar

can I switch ignition cylinder with a different ignition cylinder w/key in a 2004 chevy Malibu without having to use a passcode

User Avatar

The ignition is removed by taking down the kick panel below the steering wheel. They are a bear to get out. Make sure you have the whole cylinder assembly because they most often break apart when you remove them.

User Avatar

how to remove key stuck in ignition switch in Chevy colbalt

User Avatar

The ignition lock cylinder on a 2006 Chevy Cobalt is removed by popping off the steering column cover and inserting a screwdriver into the release hole. The cylinder can then be pulled from its housing and replaced.

User Avatar

Remove the retaining ring from the top of your 1989 Chevy Corvette ignition switch. Slide the ignition switch out and remove the wiring harness.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.